Resistance to air flow at 50 L/min: 0.25 cmH
Resistance to air flow at 100 L/min: 0.95 cmH
Dead space (approx): S/M size - 76 ml
Operating Temperature: Do not expose the mask to temperatures above 140˚F ( 60C˚)
1. Remove the mask and the headgear from the package.
2. Place the headgear on a table, label side down with the narrowest part close to you.
3. Set the mask with the gel side down onto the center of the headgear.
4. Take each headgear strap and connect it to its respective location on the mask by looping the Velcro strap
through the headgear slots and attaching it back to itself (Figure 1).
5. Once the headgear has been properly attached to the mask, follow the fitting tips below to fit the mask:
6. Detach one Velcro strap by sliding the Velcro
head and center the mask on the face.
7. Find the detached Velcro
8. Be sure the headgear straps are parallel and the headgear is fully extended and flat across the back of the
head (Figure 3).
9. Adjust the bottom headgear straps by using the Velcro
parallel to the face and that there is equal tension from the headgear on both sides. After tightening, make sure
the Active Headgear Connector
NOTE: Do NOT over tighten the headgear.
NOTE: The Touchless Spacebar
10. Adjust the upper headgear straps by using the tabs. Be sure they are tightened evenly and that the
Touchless Spacebar
TM
is parallel to the forehead (Figure 5).
NOTE: The Touchless Spacebar
(Figure 6).
11. Adjust the bottom headgear straps to make sure the bottom of the mask is sealed comfortably on the face.
12. For optimal seal and comfort, mask should be snug, but not tight. Adjust the tension by detaching the
Velcro
®
straps, tightening or loosening the straps, and reattaching the Velcro
13. Connect the mask tubing assembly to the positive airway pressure device tubing and turn the device on to
the prescribed pressure (Figure 7).
14. Turn head from side to side while lying on the bed and identify areas of leak that may prevent sleep.
15. In the event of leaks, tighten the Velcro
headgear.
®
Innova
is a registered trademark of Sleepnet Corporation.
Visit our website at www.sleepnetmasks.com.
ESPAÑOL
!
ESTE PRODUCTO NO SE FABRICA CON LÁTEX DE CAUCHO.
La máscara nasal de ventilación Innova
presión positiva en las vías respiratorias, como las terapias CPAP o de dos niveles. La máscara es para uso
exclusivo de un solo paciente en casa, en el hospital e en entornos institucionales para pacientes adultos (>66
lb/30 kg) a los que se haya prescrito una terapia CPAP o de dos niveles.
PRECAUCIÓN: Las leyes federales de los EE. UU. sólo permiten la venta de este dispositivo bajo
prescripción médica.
PRECAUCIÓN: No exponga la máscara a temperaturas superiores a los 60°C.
PRECAUCIÓN: Esta máscara puede limpiarse y utilizarse de forma repetida en una misma persona. No la
esterilice.
ADVERTENCIA: Con presiones de referencia bajas, el flujo por los orificios de ventilación puede ser
insuficiente para eliminar la totalidad del gas exhalado por el tubo y puede producirse su reinhalación.
ADVERTENCIA: Con presiones de referencia bajas, el flujo por los orificios de ventilación puede ser
insuficiente para eliminar la totalidad del gas exhalado por el tubo y puede producirse su reinhalación.
de dispositivos de presión positiva continua en las vías respiratorias y máscaras nasales.
8
TECHNICAL INFORMATION
O
2
2
M/L size - 102 ml
USER INTRUCTIONS FOR THE INNOVA
®
strap and slide the Velcro loop back on the quick release hook (Figure 2).
TM
can move freely (Figure 4).
TM
will be tilted away from the face after tightening the bottom straps.
TM
should NOT touch the forehead. It should be parallel to the forehead
®
tabs closest to the area of leak. Do NOT over tighten the
Máscara nasal de ventilación Innova
CONTENIDO: Máscara nasal de ventilación Innova
Sólo Rx
®
se ha diseñado como interfaz para la aplicación de la terapia de
ADVERTENCIAS Y PRECAUCIONES
O
®
®
loop off the quick release hook, slip the headgear over the
®
tabs. Make sure the Active Headgear Connector
HECHO EN EE.UU.
NASAL MASK
®
.
®
®
con casco
TM
is