Werbung
SPECIFIC RULES
OF SECURITY
CLOTHING
- Do not wear loose clothing or jewelry likely to be
caught by the machine.
- Hearing protection must be worn when the use
of the machine.
WORKPLACE
- Keep the surroundings of the workplace clean.
- Keep spectators and especially children away from
the work surface.
- Avoid using the machine in a damp room.
- If the use of a tool in a wet location is unavoidable,
use a power supply protected by
a Residual Differential Current (RDC) device.
SOCKET AND CABLE
- Never pull on the cable to disconnect the plug
current.
- Avoid contact of the cable with oil, grease
or rough surfaces.
- Disconnect the machines: When they are not
used, before maintenance and to change
accessories such as blades, drills and knives ...
VOLTAGE
- Connect this machine to a household outlet.
- Check that the mains voltage corresponds to
that shown on the machine's nameplate.
- Earthing is not essential because of the double
insulation of the tool.
- Check the hoses, hydraulic lines and stopping devices
if your machine is equipped with them.
Immediately stop the appliance in the event of:
- Defective plug, power cord or if the wire has
been damaged.
- Defective switch.
- Excessive production of sparks by the brushes
or spark bridges in the manifold, if the engine
is equipped.
- Smoke or bad smell caused by materials
burnt insulation.
WIRE SECTION
- Monitor the relationship between cable length
and the wire section. Too small a section causes
a decrease in tension resulting in engine problems.
Observe the following notices:
Cable length up to 15 m: Wire section 1.5 mm
Cable length from 15 m to 40 m: Wire section 2.5
mm
2
MAINTENANCE
WARNING ! Remove the plug from the socket
before carrying out any adjustment, service
or maintenance.
- Always keep the machine's ventilation slots in a good
state of cleanliness.
- Cleaning should be done with a dry or slightly damp
cloth.
- Grease the moving parts periodically.
- Do not use caustic agents for cleaning plastics.
- Any defective part must be replaced by
the manufacturer's after-sales service.
GENERAL RULES OF SECU-
RITY
CAUTION ! To reduce the risk of fire, electric
shock
and injury to persons when using power tools,
it is recommended that you always follow basic
safety precautions, including the following pre-
caution:
Read all instructions before attempting to operate this
machine and keep these instructions.
Copyright © - 2022 - Fargroup. All rights reserved.
182000-Manual-B.indd 25
182000-Manual-B.indd 25
EN
WARNING ! When using power tools, basic safety
precautions should always be observed to reduce the risk
of fire, electric shock, and personal injury, including the
following. Read all of these instructions before using this
product and save this information.
Safe operation
1 - Keep the work area clean
- Messy areas and workbenches are prone to accidents.
2 - Take into account the environment of the work
area
- Do not expose the tools to rain.
- Do not use the tools in wet environments or wet.
- Keep the work area well lit.
- Do not use the tools in the presence of liquids
or flammable gases.
3 - Protection against electric shock
- Avoid any bodily contact with earthed or earthed sur-
faces (for example pipes, radiators, stoves, refrigerators).
4 - Keep other people away
- Do not let people, especially children, not affected by the
work in progress, touch the tool or the extension and keep
them away from the work area.
5 - Store tools at rest
- When not in use, tools should be stored in a closed and
dry place, out of the reach of children.
- Do not leave the machine unattended while it is
in operation.
6 - Do not force the tool
- It will do the job better and more safely at the rate for
which it was designed.
7 - Use the right tool
- Do not force small tools to make them the work
of an industrial tool.
- Do not use the tools for purposes not intended,
for example, do not use circular saws to cut tree
branches or logs.
8 - Wear appropriate clothing
- Do not wear loose clothing or jewelry, as they can get
caught in moving parts.
- Wearing non-slip shoes is recommended for outdoor work.
- Wear a hair protection device intended to contain long
hair.
9 - Use protective equipment
- Use safety glasses.
2
- Use a normal or dust mask if the work operations
generate dust.
10 - Connect the equipment for dust extraction
- If the tool is provided for connecting equipment for dust
extraction and recovery, make sure that they are connec-
ted and used correctly.
11 - Do not use the cable / cord in bad conditions
- Never jerk the cable / cord to disconnect it from the
socket. Keep the cable / cord away from heat, lubricants
and sharp edges.
12 - Fixing the workpiece
- Whenever possible, use pliers or a vice to hold the work-
piece. This practice is safer than using the hands.
13 - Do not adopt an exaggerated attitude
- Maintain an appropriate position and balance at all times.
14 - Maintain tools with care
- Keep cutting tools sharp and clean for better and safer
performance.
- Follow the instructions for lubricating and replacing
accessories.
Plus d'info sur fartools.com
-25-
21/03/2022 15:14
21/03/2022 15:14
Werbung
