Husqvarna 240i Bedienungsanweisung Seite 30

2. Connect the battery charger to a grounded power
outlet. The charging LED flashes one time. (Fig. 58)
3. Connect the battery to the battery charger. The
charging LED comes on. Charge the battery for
maximum 24 hours. (Fig. 59)
4. Push the battery indicator button, if all the LED
indicators come on, the battery is fully charged.
5. Pull the power plug to disconnect the battery charger
from the power outlet. Do not pull the power cord.
6. Remove the battery from the battery charger.
Kickback information
WARNING:
serious injury or death to the operator or
others. To decrease the risk you must know
the causes of kickback and how to prevent
them.
A kickback occurs when the kickback zone of the guide
bar touches an object. A kickback can occur suddenly
and with large force, which throws the product in the
direction of the operator.
(Fig. 35)
Kickback always occurs in the cutting plane of the guide
bar. Usually, the product is thrown against the operator
but can also move in a different direction. It is how you
use the product when the kickback occurs that causes
the direction of the movement.
(Fig. 60)
Kickback only occurs if the kickback zone of the guide
bar touches an object. Do not let the kickback zone
touch an object.
(Fig. 35)
A smaller bar tip radius decreases the force of the
kickback.
Use a low kickback saw chain to decrease the effects of
kickback. Do not let the kickback zone touch an object.
WARNING:
prevents kickback. Always obey the
instructions.
Common questions about kickback
• Will the hand always engage the chain brake during
a kickback?
No. It is necessary to use some force to push the
front hand guard forward. If you do not use the force
necessary, the chain brake will not be engaged. You
must also hold the handles of the product stable with
two hands during work. If a kickback occurs, it is
possible that the chain brake does not stop the saw
chain before it touches you. There are also some
positions in which your hand can not touch the front
hand guard to engage the chain brake.
30
A kickback can cause
No saw chain fully
• Will the inertia release mechanism always engage
the chain brake during kickback?
No. First, the chain brake must operate correctly.
Refer to Maintenance and checks of the safety
devices on the product on page 35 for instructions
about how to do a check of the chain brake. We
recommend you to do this each time before you
use the product. Second, the force of the kickback
must be large to engage the chain brake. If the chain
brake is too sensitive, it can engage during rough
operation.
• Will the chain brake always protect me from injury
during a kickback?
No. The chain brake must operate correctly to give
protection. The chain brake must also be engaged
during a kickback to stop the saw chain. If you are
near the guide bar, it is possible that the chain brake
does not have time to stop the saw chain before it
hits you.
WARNING:
working technique can prevent kickbacks.
To start the product
1. Do a check of the power trigger and power trigger
To do a check of the power trigger
lockout. Refer to
lockout on page 35 .
2. Engage the chain brake. (Fig. 61)
3. Put the battery in the battery holder. (Fig. 62)
CAUTION:
battery is installed correctly into the
battery holder. If the battery does not
move easily into the battery holder, the
position is not correct.
4. Push on the lower part of the battery until you hear a
click sound. (Fig. 63)
5. Push and hold the start/stop button until the green
LED comes on. (Fig. 64)
To use the SavE function
The SavE function decreases the chain speed and the
power of the product.
1. Push the SavE button. The green LED comes on.
2. Push the SavE button again to disconnect the
function. The green LED goes off. (Fig. 65)
To stop the product
1. Push the start/stop button until the green LED light
goes off. (Fig. 64)
2. Push the battery release buttons and remove the
battery from the battery holder to prevent accidental
start. (Fig. 66)
Only you and the correct
Make sure that the
1951 - 001 - 23.09.2022