Making Sausages; Care And Cleaning; Disassembling The Appliance - Gastroback Design Fleischwolf Advanced Bedienungsanleitung

IMPORTANT: Do not let the motor run permanently for longer then 15
minutes on maximum power to avoid overheating. After 15 minutes turn
off the appliance and let the motor cool down for several minutes before
continuing operation. With normal load the permanent running time is 30
minutes. If the overload protection turned the appliance automatically off let the motor
cool down for a few minutes before continuing operation.
7. As soon as the last bit is minced turn the appliance off (by turning the control switch
to STANDBY) and pull the plug. Clean and disassemble the appliance right after use
and make sure that no leftover food desiccate on the appliance. Proceed according
to the instructions in chapter ›Care and cleaning‹.

MAKING SAUSAGES

1. Prepare the meat according to the instructions in chapter ›Operating- Mincing meat‹.
Season the meat as desired.
2. Assemble the sausage attachment according to the instructions in chapter ›Assemble
for making sausages‹
3. Soak the sausage skin for 10 minutes in lukewarm water. Slide the sausage skin over
the sausage attachment.
Tip:
If the skin gets stuck to the sausage attachment, wet it with some water.
4. As soon as the last bit has run through the appliance turn the appliance off (by tur-
ning the control switch to STANDBY) and pull the plug.
5. Clean and disassemble the appliance right after use and make sure that no leftover
food desiccate on the appliance. Proceed according to the instructions in chapter
›Care and cleaning‹.

CARE AND CLEANING

WARNING: Never hold your face or other body parts over the feed chute when the
motor is running because little pieces of food could be thrown out of the feed chute.
Never put foreign substance or hard objects into the feed chute.
Before the mincer is used for the first time and after each use, all parts – with the excep-
tion of the motor housing – must be thoroughly cleaned in warm soapy water. In case of
blockage proceed according to the instructions in the ›Trouble shooting guide‹.
42

DISASSEMBLING THE APPLIANCE

WARNING: To avoid injury and damages of the appliance turn the appliance off
(by turning the control switch to STANDBY - picture A) and then wait for approx. 6
seconds to be certain that the motor is no longer running. Always pull the plug before
you start disassembling or cleaning the appliance.
1. Switch off the mincer and disconnect the power supply cable from the mains. Check
that the motor has completely stopped.
2. Take the pusher and the feed pan of the feed chute.
3. Loosen the screw plug on the right side of the mincer by tur-
ning it counterclockwise until you can take the worm housing
out of the motor housing without any resistance (picture B).
4. Loosen the closing ring by turning it counterclockwise If
the closing ring is screwed on too tight you can use the
provided spanner to loosen the closing ring.
5. Take the closing ring of the worm housing and take the
accessories (worm, crossed-blade knife and grinding disc
or the sausage filling attachment and the adaptor disc)
out of the worm housing.
Note:
If the tools got stuck knock the mincer carefully on a stable cutting board. The grinding
disc should be facing up.
ATTENTION: Be careful not to damage your bench top, the cutting board or the mincer.
6. Remove meat residues. Operate as described:
ATTENTION: Never put the motor housing or the accessories in the dishwasher or use
abrasives for cleaning! This will cause discolouration and corrosion and damage the motor.
7. Wash all parts thoroughly in warm soapy water. Do not use aggressive detergents.
Soak parts with desiccated food leftovers a few minutes in warm soapy water and
use a nylon cleaning brush or cleaning sponge for cleaning. Rinse all parts with run-
ning water and dry them accurately.
WARNING: Ensure that the switch and power cord do not come into contact with
water! Should this inadvertently happen, all parts must be completely dry before the
appliance is used again. Never let water or other liquids run into the motor housing.
Never clean the power cord or the motor housing in the dishwasher, poor liquids over
the appliance or douse or dip it in water or other liquids. In case that water or other
liquids ran into the appliance while operating turn STANDBY the appliance immediately,
pull the plug and dry the appliance with a clean cloth.
43