Husqvarna 120iTK4-P Bedienungsanweisung Seite 23

Maintenance
Clean the saw chain cover.
Do a check of the connections between the
battery and the product. Do a check of the
connection between the battery and the bat-
tery charger.
Make sure that the saw head is not dam-
aged. Replace the saw head if it is damaged.
Examine the wear of the chain drive sprock-
et.
To examine the cutting equipment
1. Make sure that there are no cracks in rivets and
links and that no rivets are loose. Replace if it is
necessary. (Fig. 52)
2. Make sure that the saw chain is easy to bend.
Replace the saw chain if it is rigid.
3. Compare the saw chain with a new saw chain to
examine if the rivets and links are worn.
4. Replace the saw chain when the longest part of the
cutting tooth is less than 4 mm/0.16 in. Also replace
the saw chain if there are cracks on the cutters. (Fig.
53)
To replace the guide bar
1. Turn the locking knob counterclockwise and remove
the protective cover (A). (Fig. 54)
2. Remove the guide bar with the saw chain attached.
3. Remove the saw chain from the guide bar.
4. Remove the bolt (D) and remove the gear. Keep the
gear near.
5. Install the gear with the bolt (D) into the new guide
bar.
6. Put the saw chain in the groove of the guide bar.
7. Install the guide bar and gear (B) onto the guide bar
pin (E).
8. Install the saw chain around the drive sprocket.
Make sure that the cutting teeth point in the direction
away from the drive sprocket (C).
9. Install the protective cover (A) and turn the locking
knob clockwise.
10. Tighten the saw chain. Refer to
of the saw chain on page 24 for instructions.
To replace the saw chain
1. Turn the locking knob counterclockwise and remove
the protective cover (A). (Fig. 54)
2. Remove the guide bar with the saw chain attached.
3. Remove the saw chain from the guide bar.
4. Put a new saw chain in the groove of the guide bar.
707 - 011 - 31.10.2022
Daily
An approved Husqvarna dealer must do all servicing on the saw
Replace the chain drive sprocket after approximately 100 hours of
operation or more frequently if it is necessary.
5. Install the guide bar and gear (B) onto the guide bar
6. Install the saw chain around the drive sprocket.
7. Install the protective cover (A) and turn the locking
8. Tighten the saw chain. Refer to
To sharpen the saw chain
Information about the guide bar and saw chain
Replace a worn or damaged guide bar or saw chain with
the guide bar and saw chain combination recommended
by Husqvarna. This is necessary to keep the safety
functions of the product. Refer to
page 29 , for a list of replacement bar and chain
combinations that we recommend.
•
(Fig. 55)
•
(Fig. 56)
•
To adjust the tension
(Fig. 57)
•
(Fig. 58)
•
(Fig. 59)
Weekly
X
head.
pin (E).
Make sure that the cutting teeth point in the direction
away from the drive sprocket (C).
knob clockwise.
of the saw chain on page 24 for instructions.
WARNING:
Use protective gloves
when you use or do maintenance on the
saw chain. A saw chain that does not move
can also cause injuries.
Guide bar length, in/cm. Information about the guide
bar length can usually be found on the rear end of
the guide bar.
Number of teeth on bar tip sprocket (T).
Chain pitch, in. The distance between the drive links
of the saw chain must align with the distance of the
teeth on the bar tip sprocket and drive sprocket.
Number of drive links. The number of drive links is
decided by the type of guide bar.
Bar groove width, in/mm. The groove width in guide
bar must be the same as the chain drive links width.
Monthly
X
To adjust the tension
Accessories on
23