Husqvarna 120iTK4-P Bedienungsanweisung Seite 17

loose clothing that can catch on twigs and branches.
Do not wear jewelry, short pants, open shoes or go
with bare feet. Put your hair up safely above your
shoulders.
• Keep first aid equipment close at hand.
(Fig. 26)
Safety devices on the product
WARNING:
instructions that follow before you use the
product.
In this section the product's safety features, its purpose
and how checks and maintenance should be carried
out to ensure that it operates correctly. See instructions
under the heading Product overview on page 12 to find
where these parts are located on your product.
The life span of the product can be reduced and the risk
of accidents can increase if product maintenance is not
carried out correctly and if service and/or repairs are not
carried out professionally. If you need further information
please contact your nearest servicing dealer.
WARNING:
defective safety components. The product's
safety equipment must be inspected and
maintained as described in this section.
If your product fails any of these checks,
contact your service agent to get it repaired.
CAUTION:
All servicing and repair work
on the machine requires special training.
This is especially true of the machine's
safety equipment. If your machine fails
any of the checks described below you
must contact your service agent. When
you buy any of our products we guarantee
the availability of professional repairs and
service. If the retailer who sells your
machine is not a servicing dealer, ask him
for the address of your nearest service
agent.
To do a check of the keypad
1. Push and hold the start/stop button (A). (Fig. 27)
a) The product is on when the LED is on.
b) The product is off when the LED is off.
To start the SavE function on page 21 for
2. Refer to
the function of the SavE button (B).
3. Refer to Troubleshooting on page 26 if the warning
indicator (C) is on or flashes.
707 - 011 - 31.10.2022
Read the warning
Never use a product with
To do a check of the power trigger lockout
The power trigger lockout prevents accidental operation.
When you release the handle, the power trigger and the
power trigger lockout move back to their initial position.
(Fig. 28)
1. Make sure that the power trigger is locked when the
lockout is in its initial position. (Fig. 29)
2. Pull and release the lockout and make sure that it
moves back to its initial position . (Fig. 30)
3. Make sure that the power trigger and the lockout
move freely and that the return spring operates
correctly. (Fig. 31)
4. Start the product, see To start the product on page
21 .
5. Apply full speed.
6. Release the power trigger and make sure that the
cutting attachment stops fully.
Safety instructions for the cutting equipment
WARNING:
instructions that follow before you use the
product.
• Only use approved guide bar/saw chain
combinations and filing equipment. Refer to
Maintenance on page 22 for instructions.
• Use protective gloves when you use or do
maintenance on the saw chain. A saw chain that
does not move can also cause injuries.
• Keep the cutting teeth correctly sharpened. Obey the
instructions and use the recommended file gauge. A
saw chain that is damaged or incorrectly sharpened
increases the risk of accidents.
(Fig. 32)
• Keep the correct depth gauge setting. Obey the
instructions and use the recommended depth gauge
setting. Too large depth gauge setting increases the
risk of kickback.
(Fig. 33)
• Make sure that the saw chain has the correct
tension. If the saw chain is not tight against the guide
bar, the saw chain can derail. An incorrect saw chain
tension increases wear on the guide bar, saw chain
and chain drive sprocket. Refer to
page 29 .
(Fig. 34)
• Do maintenance on the cutting equipment regularly
and keep it correctly lubricated. If the saw chain is
not correctly lubricated, the risk of wear on the guide
bar, saw chain and chain drive sprocket increases.
(Fig. 35)
Read the warning
Accessories on
17