Briggs & Stratton Vanguard 10V000 Bedienungsanleitung Seite 11

6. Install and tighten the dipstick again.
7. Connect the spark plug wire(s) to the spark plug(s). Refer to the Remove Oil
section.
Change Gear Reduction Oil
Some engines are equipped with a Gear Reduction Unit. If equipped, refer to the steps
for one of the Gear Reduction Units that follow.
2:1 Chain Reduction Unit
If the engine is installed with a 2:1 chain reduction unit (G, Figure 25), an oil change is
not necessary. The oil in the engine also lubricates the chain reduction unit.
2:1 Wet Clutch Reduction Unit
If the engine is equipped with a 2:1 wet clutch reduction unit, do the steps that follow:
1. Remove the dipstick (A, Figure 26).
2. Remove the drain plug (B, Figure 26), and drain the oil into an approved container.
3. Install and tighten the oil drain plug (B, Figure 26).
4. Slowly add oil into the oil fill (C, Figure 26). See Specifications section.
5. Install the dipstick (A, Figure 26).
6. Remove the dipstick (A, Figure 26) and check the oil level. The correct oil level is at
the top of the full indicator (D) on the dipstick.
7. Install the dipstick (A, Figure 26).
6:1 Gear Reduction Unit
If your engine is equipped with a 6:1 gear reduction unit, do the steps that follow:
1. Remove the oil fill plug (A, Figure 27) and the oil level plug (B).
2. Remove the oil drain plug (C, Figure 27) and drain the oil into an approved
container.
3. Install and tighten the oil drain plug (C, Figure 27).
4. Slowly add gear reduction oil (80W-90) into the oil fill hole (D, Figure 27). Continue
to add the gear reduction oil (80W-90) until the oil comes out of the oil level hole
(E).
5. Install and tighten the oil level plug (B, Figure 27).
6. Install and tighten the oil fill plug (A, Figure 27).
NOTE: The oil fill plug (A, Figure 27) has a vent hole (F) and must be installed on the
top of the gear case cover as shown.
Servicing the Air Filter
WARNING
Fuel vapors are flammable and explosive. Fire or explosion could result in burns
or death.
• Do not start and operate the engine with the air cleaner assembly (if equipped)
or the air filter (if equipped) removed.
NOTICE
Do not use pressurized air or solvents to clean the filter. Pressurized air could result in
damage to the filter and solvents will dissolve the filter.
See the Maintenance Schedule for servicing requirements.
Different models will use a foam or a paper filter. Some models could also have an
optional pre-cleaner that can be cleaned and used again. Compare the illustrations in
this manual with the type installed on your engine and service as follows.
Paper Air Filter
1. Loosen the fastener(s) (C, Figure 28).
2. Remove the cover (A, Figure 28) and the filter (B).
3. To loosen debris, lightly tap the filter (B, Figure 28) on a hard surface. If the filter is
dirty, replace it with a new filter.
4. Install the filter (B, Figure 28).
5. Install the cover (A, Figure 28) with the fastener(s) (C). Make sure that the
fastener(s) is tight.
Paper Air Filter - Low Profile
1. Move the latch (A, Figure 29) to unlock the cover (C).
2. Push in the tabs (B, Figure 29) and remove the cover (C).
3. Remove the filter (D, Figure 29).
4. To loosen debris, lightly tap the filter (D, Figure 29) on a hard surface. If the filter is
dirty, replace it with a new filter.
5. Install the filter (D, Figure 29).
6. Install the cover (C, Figure 29). Move the latch (A) to the locked position.
NOTE: Check the fit of the foam seal (E, Figure 29). Make sure that the perimeter foam
seal is correctly seated in the channel (F).
Servicing the Fuel System
WARNING
Fuel and its vapors are flammable and explosive. Fire or explosion could result in
burns or death.
• Keep fuel away from sparks, open flames, pilot lights, heat, and other ignition
sources.
• Frequently examine the fuel lines, fuel tank, fuel cap, and connections for cracks
or leaks. Replace damaged parts.
• If fuel spills, wait until it dries before you start the engine.
Fuel Strainer, if installed
1. Remove the fuel cap (A, Figure 30).
2. Remove the fuel strainer (B, Figure 30).
3. If the fuel strainer is dirty, clean or replace it. If you replace the fuel strainer, make
sure to use an original equipment replacement fuel strainer.
Storage
Fuel System
Refer to Figure: 31.
WARNING
Fuel and its vapors are flammable and explosive. Fire or explosion could result in
burns or death.
Fuel Storage
• Because pilot lights or other ignition sources can cause explosions, keep fuel or
equipment away from furnaces, stoves, water heaters or other appliances that
have pilot lights.
Keep the engine level (normal operating position). Fill the fuel tank (A, Figure 31) with
fuel. For fuel expansion, do not fill above the fuel tank neck (B).
Fuel can become stale when kept in a storage container for more than 30 days. The use
of an alcohol-free fuel stabilizer and ethanol treatment in the fuel storage container is
recommended to prevent fuel degradation and keep the fuel fresh.
When you fill the fuel container with fuel, add an alcohol-free fuel stabilizer as specified
by the manufacturer's instructions. If gasoline in the engine has not been treated with a
fuel stabilizer, it must be drained into an approved container. Operate the engine until it
is out of fuel.
Engine Oil
While the engine is still warm, change the engine oil. Refer to Change the Engine Oil
section.
Troubleshooting
Assistance
For assistance, contact your local dealer or go to BRIGGSandSTRATTON.COM or call
1-800-444-7774 (in USA).
Specifications and Service Parts
Specifications Model: 10V000
Displacement 10.313 ci (169 cc)
Bore 2.44 in (62 mm)
Stroke 2.204 in (56 mm)
Oil Capacity 18 - 20 oz (,54 - ,59 L)
2:1 Wet Clutch Reduction 10W-30
- Oil Type
2:1 Wet Clutch Reduction 10 oz (,30 L)
- Oil Capacity
6:1 Gear Reduction - Oil 80W-90
Type
6:1 Gear Reduction - Oil 4 oz (12 L)
Capacity
Spark Plug Gap .030 in (,76 mm)
Model: 12V000
12.387 ci (203 cc)
2.677 in (68 mm)
2.204 in (56 mm)
18 - 20 oz (,54 - ,59 L)
10W-30
10 oz (,30 L)
80W-90
4 oz (12 L)
.030 in (,76 mm)
11