Demolition And Disposal - Berkel HOME LINE PLUS-Serie Gebrauchsanleitung

- back of the blade: with the
extractor holding the blade,
press a damp cloth on the sur-
face of the blade and slowly
move it from the center out-
wards, as shown in the figure
(Fig.D2). Dry it, in the same way,
using a dry cloth;
- blade protector shell: clean
the blade protector shell using,
if necessary, a semi-rigid nylon
brush
- machine body: clean with a
damp cloth or a soft sponge.
Carefully dry all parts of the
machine using a soft cloth.
Finally, assemble the:
- blade:
1) rotate the pulley until the
red pin is positioned on the
left side (or towards the op-
erator) (Fig.G)
2) insert the blade into the
pulley making sure to insert
the red pin into one of the
three holes on the blade
3) fix the blade to the pulley
by turning the central knob
of the extractor clockwise
while holding one of the two
side knobs firmly
4) remove the extractor from
the blade by unscrewing the
two side knobs making sure
that the blade is firmly fixed
to the pulley.
- blade cover:
1) replace the blade cover as
in the figure E;
2) slightly rotate the blade
cover clockwise until it locks
into its initial position;
- meat table:
lift the meat table and move
it to the cutting position,
pressing down lightly until it
clicks (Fig. B).
MAINTENANCE
Blade maintenance
Cleanse the blade regularly to
keep it sharp and functional.
Do not wash the blade in the
dishwasher.
Slice maintenance
To keep the linear sliding of
the machine in optimal condi-
tions, oil the bars using Berkel
lubricants, the use of other oils
could damage the sliding.
SERVICE
No replacement parts are sup-
plied in the package. All repair
and replacement
(such as replacement or repair
of the blade, belt, electrical
components, structural parts,
etc.) must be carried out solely
by persons authorised by the
manufacturer.
If a repair is required, it is ad-
visable to return the machine
to the manufacturer or to an
Authorised Service Centre.
For information about services
centres, contact:
service@berkelinternational.
com.
!
WARNING! The blade
must be replaced when
the distance between the
edge of the blade itself and
the internal edge of the pro-
tection exceeds 5 mm.
WARRANTY
AND RESPONSIBILITY
The manufacturer
machines with a warranty of
24 months starting from the
date of purchase. The warran-
ty covers only those defects if
used properly and according
to the conditions of use provid-
ed by the manual. The warran-
ty does not cover defects due
to transport, the purchaser's
incompetence or negligence,
improper installation or place-
ment, damage due to wear, or
voltage greater than 10% of the
nominal value. Furthermore,
the warranty does not cover
components inherently sub-
ject to wear, such as the blade
and sharpener wheels, except
in the case of obvious produc-
tion defects.
17
The manufacturer declines any
direct and indirect responsibil-
ity stemming from:
- failure to observe the instruc-
tions in this manual;
- use which does not conform
to regulations in the country of
installation;
- unauthorised
and/or repairs on the machine;
activities - use of non original accesso-
ries or replacement parts;
- exceptional event.
The transfer of machine own-
ership involves the immediate
release from any responsibility
by the manufacturer, with the
exception of compliance with
Directive 2006/42/EC (liability
for any manufacturing defect
of the product).
The identification plate at the
base of the machine registers
the manufacturer, the ma-
chine, technical information
and the CE marking.
DEMOLITION
AND DISPOSAL
The machine is composed of:
- aluminium alloy;
- inserts and various compo-
nents in stainless steel;
- electrical parts and electrical
provides cables;
- electric motor;
- plastic, etc.
If disposal is entrusted to a
third party, contact only au-
thorised companies for dispos-
al of the materials mentioned
above. The device contains ma-
terials which can be recovered
or recycled. Proper separate
collection facilitates recycling.
At the end of machine life,
deposit in your device at a col-
lection point. Information on
disposal can be obtained from
local authorities.
modifications