Inhaltsverzeichnis
Werbung
GB
•
Make sure that the piece of work being sawn off does not get stuck in place, do not hold it or
clamp it and no not secure it against the stop. It must be able to move freely along the side of
D
the saw blade. When this is not possible the piece of work being sawn can be trapped by the
saw blade and be flung about.
•
Avoid placing your hands anywhere where in the case of a sudden movement one or both
NL
hands can come into contact with the saw blade.
•
Let the saw get up to full revolutions before you start sawing.
•
Press the saw head downwards so that the motor is not overloaded and the saw blade does
F
not get jammed.
•
If you need to remove jammed material, first let the saw blade stop turning completely,
switch the motor off and take the plug out of the socket.
E
•
At the end of the sawing process, keep the saw head downwards, switch off the machine
and wait until all moving parts has come to a stop before you take your hands off the
machine.
P
Motor
•
Connect the machine to a 220/230 V socket.
I
•
If the motor does not start, immediately release the switch. Take the plug out of the socket.
Check that the saw blade can turn freely. If so, try starting the machine again.
S
To prevent damaging the motor is must regularly freed of chips and dust to ensure
correct cooling.
FIN
•
If the motor suddenly stops while sawing, let go of the switch immediately. Loosen the saw
N
blade from the piece of work, after which sawing can continue.
•
Using long cables of too small a diameter can result in loss of voltage, which can lead to
problems with the motor.
DK
•
For a length up to 15 metres a cable must be used with a diameter of 1.5 mm
•
For a length of between 15 and 40 metres a cable must be used with a diameter of 2.5 mm
3. ASSEMBLYAND ACCESSORIES
Installation of the mitre saw
Fig. 1 - 3
•
Remove the machine from the packaging.
•
Position the extension pieces (6) on the sides of the machine and fix them in place with the
Allen screw (8) using the Allen key (17).
•
Position the machine so that you can easily reach the underside. Press the five rubber caps
supplied into the holes underneath at the corners of the footplate. Then put the machine
upright again.
•
Hold the handgrip and move the saw slightly downwards and then pull the locking device
(5) out slightly so that the machine comes free.
Note: Never use the mitre saw without the extension pieces supplied. Make sure that they are
correctly mounted.
8
4. FUNKTION
Brug af kap- og geringssaven
Før brug skal man altid kontrollere for fejl og defekter!
•
Indstil maskinen i den ønskede savevinkel.
•
Sæt stikket i stikkontakten.
•
Hold materialet godt fast i venstre side og hold god afstand til savklingen.
•
Tænd for maskinen på afbryderen (1).
•
Savklingen skal være oppe på fulde omdrejninger, før savklingen føres ned på arbejdsemnet.
•
Med knappen (2) hæves den beskyttende afskærmning.
•
Nu føres savklingen langsomt nedad, så savklingen saver gennem arbejdsemnet og ned i
spalten i bordet. Tryk ikke for hårdt ned på saven. Giv maskinen tid til at save gennem
arbejdsemnet.
•
Før maskinen forsigtigt op igen og sluk den ved at slippe afbryderen (1).
5. SERVICE & VEDLIGEHOLDELSE
Sørg for at maskinen ikke står under strøm, når der udføres
vedligeholdelsesarbejder på mekanikken.
Maskinerne fra Ferm er udviklet til at fungere længe uden problemer med et minimum af
2
.
vedligeholdelse. Ved at rengøre maskinen regelmæssigt og behandle den korrekt, bidrager De
2
.
til en længere levetid for maskinen.
Fejl
For det tilfælde, at maskinen ikke fungerer korrekt, er herunder angivet en række mulige
årsager med tilhørende løsningsforslag.
•
Motoren starter ikke.
•
Savsnittet er ikke jævnt (takket).
Ferm
Ferm
•
Stikket er ikke sat i stikkontakten.
•
Ledningen er i stykker.
•
Afbryderen er defekt. Tag maskinen med
til forhandleren for reparation.
•
Savklingen skal slibes.
•
Savklingen er monteret, så den vender
forkert.
•
Der sidder harpiks eller savsmuld på
savklingen.
•
Savklingen er ikke egnet til dette
arbejdsemne.
GB
D
NL
F
E
P
I
S
FIN
N
DK
97
Werbung
Inhaltsverzeichnis
