Inhaltsverzeichnis
Werbung
GB
•
Højde- og/eller geringsgrebet blokeres.
D
•
Motoren har svært ved at nå op på fulde
omdrejninger.
NL
•
Maskinen ryster ekstremt meget.
F
•
Maskinen bliver meget varm.
•
Elektromotoren går ujævnt.
E
P
Reparationer må udelukkende udføres af en autoriseret installatør eller et
autoriseret serviceværksted.
I
Rengøring
S
Rengør regelmæssigt maskinkappen med en blød klud, helst efter hvert brug. Sørg for at
ventilationshullerne er fri for støv og snavs. Brug en blød klud, der er vædet i sæbevand til at
fjerne hårdnakket snavs. Brug ingen opløsningsmidler, så som benzin, alkohol, ammoniak, osv.
FIN
Den slags stoffer beskadiger kunststofdelene.
N
Smøring
Maskinen behøver ingen ekstra smøring.
DK
Fejl
Skulle en fejl opstå, f.eks. pga. slidtage af en enhed, kontakt venligst serviceadressen på
garantibeviset. På bagsiden af denne manual finder du en tegning med alle dele, der kan
bestilles.
Miljø
For at undgå transportbeskadigelse leveres maskinen i en solid emballage. Emballagen er så
vidt muligt lavet af genbrugsmateriale. Genbrug derfor emballagen.
Defekte og/eller kasserede elektriske eller elektroniske maskiner skal afleveres på
en genbrugsplads.
Garanti
Læs det separat vedlagte garantikort for garantibetingelserne.
98
•
Savsmuld og/eller støv skal fjernes.
•
Forlængerledningen er for tynd og/eller
for lang.
•
Netspændingen er mindre end 230 V.
•
Savklingen er beskadiget.
•
Ventilationsrillerne er tilstoppede -
Rengør dem med en tør klud.•
Kontaktkullene er slidt op - Udskift
kontaktkullene eller kontakt
forhandleren.
•
When sawing profile sections the work must be carried out such that the piece of work
cannot slide away and the saw blade cannot become jammed.
Aprofiled piece of work must lie flat or be held in place by an attachment so that toppling or
sliding during the work is prevented.
•
Round pieces of work such as tubes must be well secured, otherwise these can revolve and
the danger exists that the saw blade catches in them. Always keep the piece of work on the
table and against the stop using a suitable accessory or attachment.
•
Make sure that the piece of work does not have any nails or other foreign objects in it.
User safety
•
Make sure you have a clean and tidy working environment.
•
Make sure the working environment is well lit.
•
The user of the machine must be instructed in the use, adjustment and operation of the
machine.
•
Use a dust mask or dust hood to prevent the inhalation of (harmful) dust.
•
Wear gloves when you exchange the saw blade or when rough material is to be sawn. It is
best to keep saw blades in a separate holder to prevent anyone getting hurt.
•
When the machine is equipped with a laser, this may not be replaced by a different type of
laser. Repairs may only be carried out by the laser manufacturer or a recognised specialist.
•
The operator should wear ear protectors to reduce any damage to hearing.
•
To prevent accidents occurring by the accidental switching on of the machine, the plug must
always be pulled out of the socket before adjustment of the stop or the saw head is carried
out, when changing blades or accessories, and when maintaining the machine.
•
To prevent electric shocks, when plugging the plug into the socket the metal pins must not
be touched in any way whatsoever.
•
Never use the cord to pull the plug out of the socket. Keep the cord away from oil, heat and
sharp objects.
•
Never apply a cleaning or lubrication agent to a saw blade that is still revolving.
•
To prevent fires, never use the machine in the vicinity of flammable liquids, vapours or
gases.
•
Always use original accessories: others may cause wounding.
•
Always choose the right saw blade in relation to the material to be sawn.
Transporting and moving
•
Check that all locks and tensioning devices are secure.
•
Do not lift the machine by the extension pieces (for the stabilisation of the saw), but by the
solid underside of the machine.
While the machine is in use
With frequent use of the machine, do not let routine lead to mistakes. Remember that a slight
lack of concentration can lead to serious injuries in a fraction of a second.
•
Before beginning to saw, make sure that the protective hood is in the right position.
•
Before cutting the first cut, let the machine run for a short while. If you hear any unusual
sounds or observe any strong vibration, turn the machine off and take the plug out of the
socket, and then find the cause of the problem. Do not switch the machine on again until the
cause has been found and the fault repaired.
Ferm
Ferm
GB
D
NL
F
E
P
I
S
FIN
N
DK
7
Werbung
Inhaltsverzeichnis
