Inhaltsverzeichnis
Werbung
UK
METALBÅNDSAV
D
Tallende i den følgende tekst korresponderer med afbildningerne på side 2 -7
Advarsel! Brugsanvisningen til elektriske maskiner skal altid gennemlæses før
NL
brug. På den måde får du bedre kendskab til produktet og undgår unødige risici.
Gem denne brugsanvisning et sikkert sted til senere brug.
F
Indhold
1.
Tekniske specifikationer
2.
Sikkerhedsforskrifter
E
3.
Montage og indstillings forskrifter
4.
Anvendelse
P
5.
Fejlfinding
1. TEKNISKE SPECIFIKATIONER
I
Netspænding
S
Netfrekvens
Effektoptagelse
Ubelastet omdrejningstal
SF
Maks. savdybde
Max. savekapacitet 90º
Max. savekapacitet 45º
N
Savklingelængde
Vægt
LpA(lydtryk)
DK
LpA(Lydkraftsniveau)
Vibrationsværdi
Produktinformation
Fig. 1
Der må ikke benyttes savklinger, som er beregnet til at skære i træ.
1
Tænd/sluk-kontakt
2
Befæstigelseshul
3
Savklinge
4
Savklingebeskyttelse
5
Savklingehylster
6
Dæksel
7
Højdeindstiller til øverste savklingehjul
8
Låseknap til smigvinkel
9
Skruestik
10 Længdestop
11 Stativ
106
230V
50Hz
400W
20/29/50 m/min
90x120mm
Ø90 mm; 90 x 85 mm
Ø40 mm; 38 x 38 mm
1300mm
31kg
60.8 dB(A)
73,8dB(A)
< 2,5 m/s
2
Ferm
Adjusting the speed
Fig. O
The machine can operate at various speeds. For sawing thick metal, choose one of the two high
speeds. For sawing thin metal, choose the low speed.
•
Slacken the screw (42).
•
Open the cover (43).
•
Slacken the nuts (44) a few threads.
•
Slacken the tightening screw (45) a few threads to release the tension.
•
For sawing at high speed, place the V-belt (46) over one of the front pairs of rollers (47 &
48).
•
For sawing at low speed, place the V-belt (46) over the rear pair of rollers (49).
•
Tighten the tightening screw as much to tension the V-belt.
•
Tighten the nuts.
•
Close the cover.
•
Replace the screw (42).
Before tightening the V-belt, make sure that the machine is switched off and
unplugged.
Lubrication
Fig. L
•
Regularly apply a drop of oil to lubricate the guide rollers on the saw band guides.
Transporting the machine
Fig. P
•
Remove the lock screw (50).
•
Align the eye (51) of the link (52) with the threaded hole (53) so that the head is locked in the
lowest position. Keep the chain as short as possible.
•
Replace the lock screw.
•
Carry the machine at the table (17) while transporting the machine.
5.
SERVICE & MAINTENANCE
Make sure that the plug is removed from the mains when carrying out maintenance
work on the motor.
The machines have been designed to operate over a long period of time with a minimum of
maintenance. Continuous satisfactory operation depends upon proper machine care and
regular cleaning.
Cleaning and maintenance
The machine does not require any special maintenance.
•
Regularly clean the ventilation slots.
Ferm
GB
D
NL
F
E
P
I
S
SF
N
DK
15
Werbung
Inhaltsverzeichnis
