Inhaltsverzeichnis
Werbung
GB
4. Is the protective cap working properly?
5. Are you wearing safety goggles?
6. Is the saw blade not rubbing against
anything?
It is absolutely necessary to take these
points into consideration before you
start work!
Lengthwise sawing
•
Secure the fence to the correct measuring
position and remove the cut-off guide from the
bench carriage.
•
Turn the saw blade approximately 2 mm
higher than the total thickness of the wood to
be sawn.
•
Press the wood lightly towards the bench and
let it glide against the cut-off fence.
Remain at least 3 cm. from the front of
the saw blade before you switch on the
engine. The side of the wood which is
against the fence must be completely
straight. Keep your hands at least 10
cm away from the saw track to be
followed.
•
Switch on the engine and wait until the saw
blade has reached the maximum number of
revolutions before you start sawing.
•
While you press the wood against the bench
and the fence, you can carefully push the
wood through the saw blade without forcing it.
•
Never pull the workpiece backwards. If
necessary, switch off the engine first without
altering the position of the workpiece.
Lengthwise sawing with a(vertical) mitre
This method is practically the same, except that
the saw blade is placed at the angle required.
With this type of method the fence may
only be along the righthand side of the
sawblade.
Lengthwise sawing of narrow workpieces
Assume that this process is extremely
dangerous.
Take all the necessary safety measures and
continually push the workpiece through (until
behind the saw blade) using a synthetic aid
instead of by hand.
10
Crosswise sawing
•
Remove the fence and apply the cross-cut
fence in the righthand carriage.
•
Adjust the height of the saw blade (see
lengthwise sawing).
•
Press the workpiece against the cross-cut
fence and keep at least 2,5 cm distance from
the front of the saw blade.
•
Switch on the engine and wait until the
maximum number of revolutions has been
reached.
•
Press the workpiece against the fence and
the bench. Carefully push the wood through
the saw blade. Continue until behind the saw
blade. Then switch off the engine and keep
this position until the saw blade has stopped
completely before you remove the wood.
•
Never pull the wood back. If necessary, switch
the engine off and keep the position until the
saw blade has stopped completely.
Crosswise sawing with a vertical mitre
This method is practically the same, except that
the saw blade is placed in the angle required.
Only place the cross-cut fence on the
righthand side of the saw blade. Never
saw too small pieces of wood. Never
use your hands to carry out difficult
operations.
Crosswise sawing with a horizontal mitre
With this method the cross-cut fence must be
secured at the angle required. Keep the
workpiece pressed firmly against the cross-cut
fence and the bench before you start cutting off.
5. MAINTENANCE
Make sure that the machine is not live
when carrying out maintenance work on
the motor.
The machines have been designed to operate
over a long period of time with a minimum of
maintenance. Continuous satisfactory operation
depends upon proper machine care and regular
cleaning.
Malfunctions
In the case that the machine is not functioning
properly, we give a number of possible causes
and appropriate solutions below.
BORDSAV
Brugsanvisningen til elektriske
maskiner skal altid gennemlæses før
brug. På den måde får du bedre
kendskab til produktet og undgår
unødige risici. Gem denne
brugsanvisning et sikkert sted til senere
brug.
Indhold
1. Tekniske specifikationer
2. Sikkerhedsforskrifter
3. Montage og indstillings forskrifter
4. Arbejdsanvisninger
5. Vedligeholdelse
1. TEKNISKE
SPECIFIKATIONER
Spœnding
Frekvens
Optaget effekt
Omdrejninger, ubelastet
Savklinge
Tænder
Bordmål
Vœgt
Lpa (lydtryk)
Lwa (lydeffekt)
Vibrationsværdi
Beskrivelse
Fig. A
1. Beskyttelseskappe
2. Længdeanslag
3. Indsats til bord
4. Arm til geringsindstilling
5. Arm til højdeindstilling
6. Måleanordning til længdeanslag
7. Til/fra-afbryder
8. Termisk sikring
9. Arbejdsbord
Kontroller maskinen, løsdele og tillbehør for
transportkade.
Ferm
Ferm
2. SIKKERHEDSFORSKRIFTER
Forklaring til symboler
Risiko for personskade eller
beskadigelse af materiale.
Angiver elektrisk spænding. Kontroller
altid om netspændingen svarer til
værdien på typeskiltet.
Særlige sikkerhedsforskrifter
1. Ved brug af savblade med tænder af hærdet
metal anbefales det at anvende blade med
negativ eller moderat positiv skærevinkel.
Brug ikke savblade med dybt udskårne
tænder, da disse kan gribe
beskyttelseskappen.
2. Pas på: Montér først alle delene omhyggeligt,
inden du påbegynder arbejdet. Følg den
angivne fremgangsmåde.
3. Når du ikke er fortrolig med at arbejde med en
230-240 V
sådan maskine, anbefales det, at du lader dig
50 Hz
underrette om maskinens virkemåde af
1500 W
fagfolk, en instruktør eller teknikker.
4500/min
4. Arbejdsemnet skal altid klemmes eller trykkes
254x16x2,8mm
fast mod savføringen, inden bearbejdningen
Z40
udføres. Anvendelsen af alle mulige slags
667x430 mm
klemanordninger foretrækkes frem for kun at
37 kg
bruge hænderne til at klemme arbejdsemnet
99,3 dB(A)
fast med.
112,3 dB(A)
5. Vigtigt: Når arbejdsemnet fastholdes med
1,16 m/s
2
hænderne under bearbejdningen, skal
afstanden til savbladet være mindst 100 mm.
6. Tryk altid arbejdsemnet mod bordet.
7. Sørg for, at savbladet altid er skarpt og
kontrollér regelmæssigt, at bladet roterer frit
uden udsædvanlige svingninger. Hvis dette ikke
er tilfældet, skal savbladet udskiftes om muligt.
8. Lad maskinen dreje frit, indtil det maksimale
omdrejningstal er opnået, inden
bearbejdningen påbegyndes.
9. Sørg for, at ventilationshullerne på bagsiden
og undersiden af bordsavbænken og
elektromotoren altid er fri for støv. Dette øger
maskinens levetid. Ophobning af støv skal
undgås.
10.Lås altid de forskellige gradindstillinger, inden
bearbejdningen påbegyndes.
11. Køb udelukkende tilpassede savblade, der er
egnet til et omdrejningstal på mindst 6.000
o./minut.
12.Brug kun savblade, der er egnede til
savbænken. Det er meget farligt at anvende
DK
67
Werbung
Inhaltsverzeichnis
