GB
•
Do not use the machine before it has been assembled and installed in accordance with the
instructions.
D
•
Do not perform any designing, mounting or assembling activities on the workbench while
the machine is switched on.
•
Switch off the machine and clean the saw table before you leave the machine unattended.
NL
Switch off immediately if
•
The band saw machine becomes overheated.
F
•
The cord and/or plug are defective or damaged.
•
The switch is defective.
•
Insulation material starts to smell or burn.
E
Electrical safety
When using electric machines always observe the safety regulations applicable in your country
P
to reduce the risk of fire, electric shock and personal injury. Read the following safety
instructions and also the enclosed safety instructions. Keep these instructions in a safe place!
I
Always check that the power supply corresponds to the voltage on the rating plate.
S
Replacing cables or plugs
Immediately throw away old cables or plugs when they have been replaced by new ones. It is
SF
dangerous to insert the plug of a loose cable in the wall outlet.
Using extension cables
N
Only use an approved extension cable suitable for the power input of the machine. The
minimum conductor size is 1.5 mm
completely.
DK
3.
ASSEMBLY
Mounting the machine
Fig. B1 & B2
The machine can be set up in two ways: for use an a workbench (fig. B1) and for use with the
support (fig. B2).
The machine must be screwed to a workbench.
Mounting the machine for use on a workbench:
•
Mark the position of the mounting holes (2) on the workbench.
•
Drill holes at each of the marked positions, adjusting the diameter and depth of the holes to
the screws used.
•
Place the machine on the workbench and insert the screws into the mounting holes.
•
Firmly tighten the screws.
Mounting the machine for use with the support:
•
Follow the instructions below 'Assembling the support'.
•
Place the machine on the support (11).
10
2
. When using a cable reel always unwind the reel
Indstilling af endestoppet
Fig. J
Endestoppet forhindrer savklingen i at berøre maskinens bund.
•
Drej endestoppet (28) ind eller ud for at fastsætte den korrekte indstilling.
Montering og indstilling af længdestoppet
Fig. K
Længdestoppet anvendes til savning af arbejdsemner af samme længde.
•
Sæt stangen (29) i det dertil hørende hul (30) i siden af rammen.
•
Sæt længdestoppet (10) på stangen.
•
Indstil længdestoppet på den ønskede afstand.
•
Stram knappen (31).
4. ARBEJDSANVISNINGER
Indstilling af savevinklen
Fig. L
Standardvinklen mellem savklingen og savbordet er 90°.
•
Kontroller ved hjælp af en vinkel, at savklingens vinkel (3) i forhold til bordet (17) er 90°.
Hvis vinklen ikke er 90°, justeres den som følger:
•
Løsn skruen (32) i den nederste savklingeføring (33) et par omgange.
•
Juster savklingeføringen således, at savklingen står i en ret vinkel i forhold til bordet.
•
Stram låseknappen.
•
Gå frem på samme måde for at justere den øverste savklingeføring (34).
Kontroller at savklingen står i en ret vinkel i forhold til bordet i hele bordets længde.
Indstilling af lige gennemskæringsvinkel
Fig. M
Standardvinklen mellem savklingen og anlægsfladen er 90°.
•
Løsn låseknappen (8) et par omgange.
•
Sæt geringsvinklen til 0°.
•
Kontroller ved hjælp af en vinkel, at savklingens vinkel (3) i forhold til anlægsfladen (35) er
90°.
Ferm
Ferm
UK
D
NL
F
E
P
I
S
SF
N
DK
111