Ec Declaration Of Conformity; Safety Instructions - DeWalt DW744XP Originalanweisungen

TABLE SAW
DW744/DW744XP
Congratulations!
You have chosen a D WALT tool. Years of experience, thorough product
E
development and innovation make D
partners for professional power tool users.
Technical Data
Voltage
Type
Motor power (input)
Motor power (output)
No-load speed
Blade diameter
Blade bore
Blade body thickness
Riving knife thickness
Depth of cut at 90°
Depth of cut at 45°
Ripping capacity
Overall dimensions
Weight
L (sound pressure)
PA
K (sound pressure uncertainty)
PA
L (sound power)
WA
K (sound power uncertainty)
WA
Fuses:
Europe
U.K. & Ireland
U.K. & Ireland
NOTE: Switching activity may produce short-term voltage changes or
fluctuations. Under unfavourable conditions in public low-voltage supply
systems impairment of other appliances might appear. Disturbances will
not occur if the impedance is less than 0.25 Ohms. Sockets used for
these power tools shall be fused with 16 Amperes cut-out with an inert
characteristic.
Defi nitions: Safety Guidelines
The definitions below describe the level of severity for each signal word.
Please read the manual and pay attention to these symbols.
DANGER: Indicates an imminently
hazardous situation which, if not avoided, will result in death or
serious injury.
WARNING: Indicates a potentially hazardous situation which, if
not avoided, could result in death or serious injury.
CAUTION: Indicates a potentially hazardous situation which, if
not avoided, may result in minor or moderate injury.
NOTICE: Indicates a practice not related to personal injury
which, if not avoided, may result in property damage.
Denotes risk of electric shock.
Denotes risk of fire.
Sharp edges.
WALT one of the most reliable
E
DW744 DW744XP
LX GB/QS
V 115 230
3/4 3
W 1,500 2,000
W 850 1,300
min 3,650 3,000
-1
mm 250 250
mm 30 30
mm 2.2 2.2
mm 2.3 2.3
mm 77 77
mm 57 57
mm 625 625
mm 740 x 680 x 465 740 x 680 x 465
kg 29 29
dB(A) 107 105
dB(A) 3 3
dB(A) 92 92
dB(A) 3 3
230 V tools 10 Amperes, mains
230 V tools 13 Amperes, in plugs
115 V tools 16 Amperes, mains
EC-Declaration of Conformity
MACHINERY DIRECTIVE
DW744, DW744XP
D WALT declares that these products described under "technical data" are
E
in compliance with:
2006/42/EC, EN 61029-1, EN 61029-2-1.
These products also comply with Directive 2004/108/EC. For more
information, please contact D
E
back of the manual.
The undersigned is responsible for compilation of the technical file and
makes this declaration on behalf of D
Horst Grossmann
Vice President Engineering and Product Development
D WALT, Richard-Klinger-Straße 11,
E
D-65510, Idstein, Germany
01.08.2009

Safety instructions

When using stationary power tools, always observe the safety
regulations applicable in your country to reduce the risk of fi re,
electric shock and personal injury.
Read all of this manual carefully before operating the tool.
Save this manual for future reference.
General
1 Keep work area clean
Cluttered areas and benches can cause accidents.
2 Consider work area environment
Do not expose the tool to rain. Do not use the tool in damp or wet
conditions. Keep the work area well lit (250 - 300 Lux). Do not use
the tool where there is a risk of causing fi re or explosion, e.g. in the
presence of fl ammable liquids and gases.
3 Keep children away
Do not allow children, visitors or animals to come near the work area
or to touch the tool or the mains cable.
4 Dress properly
Do not wear loose clothing or jewellery, as these can be caught in
moving parts. Wear protective hair covering to keep long hair out of
the way. When working outdoors, preferably wear suitable gloves
and non-slip footwear.
5 Personal protection
Always use safety glasses. Use a face or dust mask whenever the
operations may produce dust or fl ying particles. If these particles
might be considerably hot, also wear a heat-resistant apron.
Wear ear protection at all times. Wear a safety helmet at all times.
6 Guard against electric shock
Prevent body contact with earthed or grounded surfaces (e.g. pipes,
radiators, cookers and refrigerators). When using the tool under
extreme conditions (e.g. high humidity, when metal swarf is being
produced, etc.), electric safety can be improved by inserting an
isolating transformer or a (FI) earth-leakage circuit-breaker.
WALT at the following address or refer to the
WALT.
E
E N G L I S H
19