ATIKA ALF 2300 Originalbetriebsanleitung Seite 15

Restart protection in case of power
failure
In case of a power failure, the device switches off automatically
(zero-voltage initiator). To restart, press the green button again.
Motor protection
The motor is equipped with a safety switch and switches off
automatically when overloaded. After a cooling-down break
(approx. 5 min), the motor may be restarted. Press the
1. reset button (motor protection)
2. green button I to restart.
Reversing switch
The motor is equipped with a reversing switch and in the case of
overload / blocking it automatically switches to reversing to re-
lease jammed material. The motor is automatically cut off after 5
seconds.
To restart press the infeed switch
If the blocking is not eliminated after several tries,
turn the adjusting knob (J) to the left.
Press the reversing switch
material is released.
Then, readjust the counter knife as described under "Adjusting
the counter knife".
Hints
Large objects or pieces of wood may be removed after the
shredder has been operated several times both in cutting
and in release direction.
Use a tamper or hook to remove jammed objects from the
hopper or ejection slot.
Always wait until the shredder has come to a complete
standstill before restarting it.
Retaining basket
The integrated retaining basket is equipped with a locking
lever and a safety cut-out device.
Power off the device before attaching or removing the re-
taining basket.
Retaining basket locked and fixed connected to
the device.
Retaining basket unlocked and disconnected
from the device. The device cannot be powered
up.
When the retaining basket is unlocked while the
device is operating the device is automatically cut
out. The LED goes out.
.
.
The jammed
W o r k i n g w i t h t h e
W o r k i n g w i t h t h e
Choose a working position alongside the equipment or behind
it.
Longer material that is protruding from the device could
spring back when it is drawn in by the blades! Observe safety
distance!
Never reach into the filling or ejection opening.
Keep your face and body away from the filling opening.
Never place hands, other parts of the body or clothing into the
filler funnel, ejection channel or in the vicinity of other moving
parts.
Check before powering the device up that:
no material residues are in the filling hopper,
−
− the retaining basket is locked.
Do not tip or tilt the machine when the motor is running.
When filling, be careful that no pieces of metal, stones, bottles
or other objects unintended for processing, enter the filling
hopper.
Immediately switch off the equipment and allow it to come to a
stop, if foreign objects enter the filling hopper or if the equip-
ment starts to make unusual noises or vibrates. Remove the
mains plug and carry out the following checks:
inspect for damage,
−
replace or repair damaged parts,
−
− check the equipment and tighten loose parts.
You must not repair the equipment yourself if you are
unauthorized to do so.
What can I shred?
Yes:
•
all types of branches up to a max. diameter, depending on
wood species and freshness.
• withered garden refuse which has lain a number of days.
Only shred in alternation with branches.
No:
•
glass, metal, plastic, plastic bags, stones, cloth, roots with soil
•
refuse which does not have a solid consistency, e. g. kitchen
waste
Special tips on shredding:
Always fill the material to be
shredded into the filling hopper
from the right.
Branches, twigs and
should be broken down immedi-
ately after they have been cut
material of this kinds gets
−
very hard when it is dry, and the maximum allowed branch
diameter to be processed has to be reduced.
Remove any side shoots from branches with a large number
of twigs.
How to shred garden waste with hight water content and a
tendency to clog
to prevent the machine from clogging, alternate waste with
−
wood containing material.
g a r d e n s h r e d d e r
g a r d e n s h r e d d e r
wood
15