Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Before further use of the machine the safety devices must
−
be checked carefully for their proper and intended func-
tion.
Check whether movable parts function perfectly and do
−
not stick or whether parts are damaged. All parts must be
correctly installed and fulfil all conditions to ensure perfect
operation of the machine.
Damaged safety devices and parts must be properly re-
−
paired or exchanged by a recognized, specialist workshop;
insofar as nothing else is stated in the instructions for use.
Damaged or illegible safety labels have to be replaced.
−
Store unused equipment in a dry, locked place out of the
reach of children.
Store the machine in a place where fuel vapours cannot come
close to open flames or sparks. Always allow the machine to
cool down before storing it.
E
l
e
c
t
r
i
c
a
l
s
a
E
l
e
c
t
r
i
c
a
l
s
a
Design of the connection cable according to IEC 60 245 (H
07 RN-F) with a core cross-section of at least
1.5 mm
for cable lengths up to 25 m
2
−
2.5 mm
for cable lengths over 25 m
2
−
Long and thin connection lines result in a potential drop. The
motor does not reach any longer its maximal power; the func-
tion of the device is reduced.
Plugs and coupler outlets on connection cables must be made
of rubber, plasticised PVC or other thermoplastic material of
same mechanical stability or be covered with this material.
The connector of the connection cable must be splash-proof.
When running the connection line observe that it does not
interfere, is not squeezed, bended and the plug connection
does not get wet.
Wind off completely the cable when using a cable drum.
Do not use the cable for purposes for which it is not meant.
Protect the cable against heat, oil and sharp edges. Do
not use the cable to pull the plug from the socket.
Regularly check the extension cables and replace them if
they are damaged.
Do not use any defective connection cables.
When working outdoors, only use extension cables especially
approved and appropriately labelled for outdoor use.
Do not set up any provisional electrical connections.
Never bypass protective devices or deactivate them.
Only hook up the machine by means of a fault-current cir-
cuit breaker (30 mA).
The electrical connection or repairs to electrical parts of
the machine must be carried out by a certified electrician or
one of our customer service points. Local regulations –
especially regarding protective measures – must be ob-
served.
If the power cord (if available) of this machine is damaged, it
must be replaced by a specific power cord that can be
purchased from the manufacturer or customer service.
Repairs to other parts of the machine must be carried out
by the manufacturer or one of his customer service points.
Use only original spare. Accidents can arise for the user
through the use of other spare parts. The manufacturer is
not liable for any damage or injury resulting from such ac-
tion.
14
f
e
t
y
f
e
t
y
C
o
m
m
i
s
s
i
o
n
i
n
g
C
o
m
m
i
s
s
i
o
n
i
n
g
Check that the machine is completely and correctly assem-
bled.
To avoid toppling, place the shredder on a firm horizontal
surface.
Do not use this machine on a paved area covered with gravel
on which thrown out material can cause injury.
The machine should only be operated in the open. Always
maintain a safe distance (at least 2 m) from walls or other
fixed objects.
Before each use, check
connection cables for defects (cracks, cuts, etc.).
−
Do not use any defective cables.
there are no damage at the machine
−
(see safety instructions).
that all screws, nuts and bolts as well as other fasteners
−
are securely tightened
that covers, deflectors and protective shields are on their
−
correct position and in good working condition.
Mains connection
Compare the voltage given on the machine model plate e.g.
230 V with the mains voltage and connect the machine to the
relevant and properly earthed plug.
Only use extension cables with sufficient core cross-section.
In case of disadvantageous power system conditions short-
term voltage reductions can occur during the starting process
of the device which can influence other devices (e.g. jittering
of a lamp). No failures are expected when the house service
connection has a continuous currect-carrying capacity greater
than 100 A per phase.
Mains fuse
2300 W
16 A time-lag
2500 W
16 A time-lag
2800 W
16 A time-lag
On / Off switch
Do not use any device where the switch can not be switched
on and off. Damaged switches must be repaired or replaced
immediately by the customer service.
Switzerland
UK
10 A time-lag
13 A time-lag
13 A time-lag
13 A time-lag
Werbung
Kapitel
Inhaltsverzeichnis
