Noise And Vibration Data - FLORABEST FBK 4 B2 Originalbetriebsanleitung

Noise and vibration data:

Noise measurement value determined in accordance with ISO 22868,
EN ISO 10517. The A-rated noise level is typically as follows:
Hedge trimmer
Sound pressure level L :
pA
Uncertainty K :
WA
Sound power level L :
WA
Guaranteed sound power level L
Uncertainty K :
WA
Pole pruner:
GB
Sound pressure level L :
pA
Uncertainty K :
WA
Sound power level:
Uncertainty K :
WA
3-section cutting blade:
Sound pressure level L :
pA
Uncertainty K :
pA
Sound power level L :
WA
Uncertainty K :
WA
Strimmer:
Sound pressure level L :
pA
Uncertainty K :
pA
Sound power level L :
WA
Uncertainty K :
WA
Wear ear protection to prevent hearing damage!
Vibration values (vector total of three directions) determined in
accordance with EN ISO 11806-1, EN ISO 10517, EN ISO 11680-1 :
Hedge trimmer
Vibration at the front handle:
Vibration at the rear handle:
Pole pruner:
Vibration on the front handle: Vibration emission value
Vibration on the rear handle:
Strimmer:
Vibration on the front handle: Vibration emission value
Vibration on the rear handle:
3-section cutting blade:
Vibration on the front handle: Vibration emission value
Vibration on the rear handle:
58
98.79 dB(A)
2.5 dB
109.53 dB(A)
: 114 dB(A)
WA
2.5 dB
97.06 dB(A)
2.5 dB
110.87 dB(A)
2.5 dB
97.64 dB(A)
2.5 dB
111.27 dB(A)
2.5 dB
99.08 dB(A)
2.5 dB
108.18 dB(A)
2.5 dB
Vibration emission value
a = 4.182 m/s 2
h,D
Uncertainty K = 1.5 m/s 2
Vibration emission value
a = 9.695 m/s 2
h,D
Uncertainty K = 1.5 m/s 2
a = 3.855 m/s 2
h,D
Uncertainty K = 1.5 m/s 2
Vibration emission value
a = 7.590 m/s 2
h,D
Uncertainty K = 1.5 m/s 2
a = 4.700 m/s 2
h,D
Uncertainty K = 1.5 m/s 2
Vibration emission value
a = 7.547 m/s 2
h,D
Uncertainty K = 1.5 m/s 2
a = 4.622 m/s 2
h,D
Uncertainty K = 1.5 m/s 2
Vibration emission value
a = 7.708 m/s 2
h,D
Uncertainty K = 1.5 m/s 2
NOTE
► The vibration level specified in these instructions has been measured
in accordance with the standardised measuring procedure specified
in EN ISO 11806-1, EN ISO 10517, EN ISO 11680-1 and can be
used to make equipment comparisons. The specified vibration emis-
sion value can also be used to make an initial exposure estimate.
WARNING!
► The vibration level varies in accordance with use and may be higher
than the value specified in these instructions in some cases. There is
a risk of underestimation of the vibration load if the appliance is used
regularly in this manner. For an accurate estimate of the vibration
load during a specific working period, the periods during which the
appliance is switched off or is running but not actually being used
must also be taken into consideration. This can significantly reduce
the vibration load over the total working period.
WARNING!
■ You can reduce the vibration risk, for example, the risk of Raynaud's
phenomenon, by taking regular breaks during which you rub your
hands together.
Explanation of the symbols on the motor unit:
Warning! Read the operating instructions before use!
Wear protective gloves!
Wear safety shoes!
Wear ear protection!
Wear a hard hat!
Wear safety goggles!
Important, hot parts. Keep a safe distance away!
1
1. Switch on device
I
ON
o
2
2. Fill fuel pump (primer)
FULL
3
3. Pull choke lever
PULL
4
4. Pull starter pull cord
PULL
CHO KE
Pull choke lever
FBK 4 B2