STIEBEL ELTRON LWZ 180 Bedienung Und Installation Seite 52

INSTALLATIoN
Settings
12.1.1 "Info" menu
 Info
  Bypass status
  Extract air temp.
  Extract air hum.
  Extract air dew pt
  Outdoor air temp.
  Outdoor air hum.
  Outdoor air dew pt
  Supply air temp.
  Exhaust air temp.
  Supply air fan control
  Supply air fan speed
  Supply air flow rate
  Exhaust air fan control
  Exhaust air fan speed
  Exhaust air flow rate
  Heating coil control
  Extract air diff. press.
12.1.2 "Diagnostics" menu
 Diagnostics
  Notification list
  Clear notification list
  Filter runtime
  Filter reset
  Filter change interval
  Device operating time
  Fan operating time
Diagnostics
Clear notification list
 
To clear the notification list, set this parameter to "On". Press "OK"
to confirm. Afterwards, "Off" is displayed again and the fault mes-
sages are deleted.
12.1.3 "Programs" menu
 Programs
  Fan program
12.1.4 "Settings" menu
 Settings
  View
  General
  Time/date
52 | LWZ 180 | LWZ 280 | LWZ 180 Enthalpie | LWZ 280 Enthalpie

Value
Off | On
°C
%
°C
°C
%
°C
°C

°C

%

rpm

m³/h

%

rpm

m³/h

%

Pa





Value


Off | On

h

Off | On

d

d

d







Value

Monday

Tuesday

Wednesday
Thursday
Friday
Saturday
Sunday

Monday - Friday
Saturday - Sunday
Monday - Sunday




Value

Code for qualified con-
tractor

Day
Hour:Minute


 Language
 Contrast
 Brightness
 Touch sensitivity
 Touch boost
 Prog. unit software
 Fan control
 Constant flow rate
 Constant pressure
 Air flow rate

Flow rate, stage 0
 Flow rate, stage 1
 Flow rate, stage 2
 Flow rate, stage 3
 Supply air flow rate offset
 Extract air diff. press.
 Diff. pressure, stage 0
 Diff. pressure, stage 1
 Diff. pressure, stage 2
 Diff. pressure, stage 3
 Favourites
 F1
F2
F3
 Humidity prot.
 Enable humidity control (A2)
 Humidity prot. interval
 Humidity threshold
 Humidity capture delay
 Intensive ventilation
 Intens. vent. time
 Heat recovery bypass
 Set room temperature
 Operating mode heat recovery bypass
 Temperature to enable heat recovery by-
pass
 Temperature to block heat recovery bypass °C
 Hysteresis for heat recovery bypass
 Temp. differential for heat recovery bypass K
 Window contact mode (A2)
(depending on unit)
 Cooling/heating, heat recovery bypass
 Frost protection
 Frost protection temp.
 Temp. to enable frost protection (A2)
German
English
Francais
Nederlands
Italiano
Polski
Cesky
Magyar
Slovensko
中文
Slovensky
日本語
1 - 10
%
1 - 10
m³/h
m³/h
m³/h
m³/h
m³/h
Pa
Pa
Pa
Pa
F1, F2, F3
Bypass status
Extract air temp.
Extract air hum.
Filter runtime
Device software version
Device software patch
Term. device serial no.
Only for qualified con-
tractors
Off
On
h
%
min
min
°C
Disabled
Bypass/window contact
Outdoor air routing au-
tomatic
Extract air routing autom.
°C
K
Without window contact
With window contact
Cooling/heating
Cooling
Heating
Only for qualified con-
tractors
°C
°C
www.stiebel-eltron.com