Stiga SILEX 103 B Bedienungsanleitung Seite 16

- Move the machine to the borders to be milled.
- Put the fork (Fig.2) into position 2 (block) working position.
- Check if the gearbox control lever (Fig.8 part.4 only 2+2 speed version) is on loose position.
- Adjust the handlebar to the requested position/height:
- How to switch the engine on (Fig.8): Open the fuel cap (for the engine equipped like this), push to halway the accelerator lever on the handlebar
(part.1) if the engine is cold, operate the starte device on the carburettor, bring the starter handle and pull energetically.
When the engine is on , after some bursts/bangs, put the starter again at rest position,
- Grasp the handlebar, insert the speed (for 2+2 speed version) pos. A slow speed, pos. B fast speed. At the beginning we recommend you to
work on position 1, slow speed.
-
Forward speed: (Fig.8) grasp the handlebars (8) lift the prevention lever (9) and then pull the forwarding lever (2) all its way.
- Reverse speed: release the clutch lever (Fig.8) (part.2) and pull towards ourselves the lever (3) on the handlebar, to lift up the back part of
the machine in order to make the rotavator to come out from the ground until the machines starts to draw back.
-
At the end of the work: when you finish the work, to stop the engine, bring the accelerator lever (1 Fig.8) to the bottom gear or press the stop
switcher on the engine.
GARAGING AND SCHEDULED MAINTENANCE
Keep attention that all the nuts ,screws and bolts are tightened in order to guarantee a good machine working on safety conditions. Leave the machine
to cool before garaging anyhow don't room it if the tank still contains some fuel as the vapours could reach some blazes or sparks. To lower the fire
danger, keep the engine , the silencer and the fuel area free from leaves, grass or greasy substances.
Perform the following operations as per the described intervals. (with the word "Hours", we mean the machine working hours).
Gearbox
(Fig. 9) Oil level control: Use oil SAE 80. Verify the oil level every 60 hours: put the machine on flat surface, remove the cap 1 and
check if the oil reaches the hole bottom edge. In case you need to fill it on you have to perform it from the hole of the cap 2. Go on with such operation
until you see the oil coming out from control cap 1. Screw both caps again.
Oil change: change the oil every 150 hours. The oil drain has to be performed when the machine is hot: remove caps 1, and 2 and tilt the machine
to a complete emptying , then put the machine on flat land, fill it in with oil through the hole of cap 2 until the oil starts coming out from control cap
1. Screw both caps again.
ATTENTION ! Waste fuel oil is a polluting material: don't waste it in the sorroundings, please apply to suitable waste material centres.
Cultivator
(Fig.10) Every time the motorcultivator is used, it is necessary that the operator controls if the screws ad the fixing nuts of the spades
on the shaft are tightened all the way home (part.3 and 9).
Reverse speed shaft
rubber cap (1). KEEP ATTENTION! once such operation has finished you must close the hole again with the rubber cap (1) because inside
the casing there are some gears/parts on motion.
NOISE LEVEL AND VIBRATION LEVEL
Measured sound pressure level with En709, Leq = 80 dB (A), with a uncertainty value K = ±1,1 dB (A). Handlebar vibration in compliance with EN
9
709 and ISO 5349. Level max detected = 7,2 m/s
(Fig.11) Every 50 working hours, grease the reverse speed shaft with the suitable greaser (1), upon disassembling of
Measured sound power level LWA = 89,1 dB (A), with a uncertainty value K = ±1,2 dB (A).
, uncertainty value K = ± 3,6 m/s
2
.
2