Troubleshooting - STIEBEL ELTRON LWZ 180 Bedienung Und Installation

INsTALLATIoN

Troubleshooting

1
2
1 Connection for the fan control cable
2 Connection for the fan power cable
f At the front of the exhaust air fan, disconnect the 3-core
power cable and the 4-core control cable.
f At the back of the exhaust air fan, disconnect the 6-core com-
mon cable for the pressure sensor and temperature sensor.
Four cores of the cable are connected to the pressure sensor
connection. Two cores of the cable are connected to the tem-
perature sensor connection.
f Remove the exhaust air fan from the appliance.
f Clean the fans with a soft brush.
Refitting the components
f Push the fan units back into the appliance.
f Turn the eccentric bolts under the fan units clockwise by
300°. The slot at the front of the eccentric bolts must be
horizontal.
f Reconnect the fan cables.
f Slide the heat exchanger back into the appliance.
f To ensure that the support bar pushes the partition under the
heat exchanger, tighten the wing screw until finger-tight. The
top three gaskets must be in contact with the heat exchanger
and become slightly deformed.
f Fit the inner front panel which ensures the appliance is air-
tight. Secure the inner front panel with seven screws.
f Hook the front panel into the hooks provided at the front of
the appliance.
f Secure the front panel with the screws at the top.
f Push the filter drawer into the appliance. The clean side of
the filters must face down.
f Hook the fascia into the appliance.
48 | LWZ 180 / L WZ 280 / LWZ 180 Enthalpie / LWZ 280 Enthalpie
Checking the condensate drain
Note
The appliance will only function correctly if the conden-
sate drain is working and is filled.
f Check the condensate drain at regular intervals – at
least once every six months.
Cleaning the air ducts
Air ducts must be checked at regular intervals and cleaned if nec-
essary. Disconnect the air ducts from the appliance or carry out in-
spection and cleaning through the extract air and supply air vents.
15. Troubleshooting
WARNING Electrocution
Disconnect the power supply by unplugging the appli-
ance from the mains before carrying out work inside
the appliance.
WARNING Electrocution
The power cable must only be replaced (for example if
damaged) by a qualified contractor authorised by the
manufacturer, using an original spare part.
Fault (Exxx)
xxx Fault Effect
--- No fault
present
1 Short circuit No control to the comfort
Supply air temperature required for
temperature passive houses of at least
sensor 16.5 °C in the supply air
2 Lead break No control to the comfort
Supply air temperature required for
temperature passive houses of at least
sensor 16.5 °C in the supply air
3 Short circuit No effect
Exhaust air
temperature
sensor
4 Lead break No effect
Exhaust air
temperature
sensor
5 No differen- To avoid build-up of
tial pressure negative pressure in the
sensor Sup- rooms, the appliance
ply air switches off both fans.
6 No differen- The unit switches off
tial pressure the exhaust air fan. The
sensor Ex- supply air fan remains in
haust air operation.
remedy
Isolate the appliance from the
power supply. Check the sensor
cable. Unplug connector X7 from
the electronic assembly. Test the
sensor.
Isolate the appliance from the
power supply. Check the sensor
cable. Unplug connector X7 from
the electronic assembly. Test the
sensor.
Isolate the appliance from the
power supply. Check the sensor
cable. Unplug connector X8 from
the electronic assembly. Test the
sensor.
Isolate the appliance from the
power supply. Check the sensor
cable. Unplug connector X8 from
the electronic assembly. Test the
sensor.
Isolate the appliance from the
power supply. Check the sensor
cable. Check the pressure hoses
for contamination and damage. If
necessary, replace the sensor and
the hose.
Isolate the appliance from the
power supply. Check the sensor
cable. Check the pressure hoses
for contamination and damage. If
necessary, replace the sensor and
the hose.
www.stiebel-eltron.com