Guidance And Manufacturer's Declaration - Electromagnetic Immunity - Therabody RecoveryAir PRO Bedienungsanleitung

Caution: Basic Safety and Essential Performance
• This system should not be used adjacent to or stacked with other equipment and that if adjacent or stacked use is
necessary, this system should be observed to verify normal operation in the configuration in which it will be used.
• The essential performance of the RecoveryAir PRO system as evaluated in IEC 60601- 1-2 includes treatment completing cycle, presentation on the display is not interfered, and treatment parameters
are not changed unintentionally.
• The following, but not limited to, are unacceptable risks that are not allowed: malfunction, non-operation when operation is required, unwanted operation when no operation is required, deviation from
normal operation that poses unacceptable risk to operator or user, component failure, change in programmable parameter(s), change in operation mode, reset to factory defaults, and false positive or
false negative alarm.
• Do not apply the device near any devices with Electromagnetic Interference (EMI), such as cell phones, Magnetic Resonance Imaging (MRI), computerized axial tomography (CT), diathermy, Radio
Frequency Identification (RFID), etc. or MR environment. EMI, RF devices or MR environments may affect the normal function of the device or would cause user injury.
Guidance and Manufacturer's Declaration – Electromagnetic Emission
The RecoveryAir PRO device is intended for use in the electromagnetic environment specified below. The customer or the user of the device should assure that it is used in such an environment .
Emission Test Compliance
The device uses RF energy only for its internal function. Therefore, its RF emissions are very low and are not likely to cause any interference in nearby electronic equipment.
IEC 61000-3-3
Guidance and Manufacturer's Declaration – Electromagnetic Immunity
The RecoveryAir PRO device is intended for use in the electromagnetic environment specified below. The customer or the user of the device should assure that it is used in such an environment.
Immunity Test
Electrostatic discharge (ESD) IEC
61000-4-2
Electrical fast transient/burst
IEC 61000-4-4
Surge
IEC 61000-4-5
Voltage dips, short interruptions and
voltage variations on power supply
input lines
IEC 61000-4- 11
Power frequency (50Hz/60Hz)
magnetic field IEC 61000-4-8
Class B The device is suitable for use in all establishments, including domestic establishments and those directly connected to the
public low-voltage power supply network that supplies buildings used for domestic purposes.
IEC 60601 Test Level
2, 4, 6, 8 kV contact
2, 4, 8, 15 kV air
±2 kV for power supply lines
±1 kV for input/output lines
±1 kV line(s) to line(s)
±2 kV line(s) to earth
<5% UT(>95% dip in Ut) for 0.5 cycles <5% UT(>95% dip in Ut) for 0.5 cycles
40% Ut (60% dip in Ut) for 5 cycles 40% Ut (60% dip in Ut) for 5 cycles
70% Ut (30% dip in Ut) for 25 cycles 70% Ut (30% dip in Ut) for 25 cycles
<5% Ut (>95% dip in Ut) for 5 sec
30 A/m
Note: UT is the AC mains voltage prior to application of the test level.
Electromagnetic Environment – Guidance
Compliance Level
2, 4, 6, 8 kV contact Floors should be wood, concrete or ceramic tile. If floors are covered
2, 4, 8, 15 kV air with synthetic material, the relative humidity should be at least 30%
±2 kV for Mains power quality should be that of a typical commercial or hospital
power supply lines
±1 kV line(s) to line(s) Mains power quality should be that of a typical commercial or hospital
±2 kV line(s) to earth
Mains power quality should be that of a typical commercial or hospital
environment. If the user of the device requires continued operation
during power mains interruptions, it is recommended that the device
<5% Ut (>95% dip in Ut) for 5 sec be powered from an uninterruptible power supply or a battery
30 A/m Power frequency magnetic fields should be at levels characteristic of a
typical location in a typical commercial or hospital environment.
Electromagnetic Environment - Guidance
environment.
environment.
EN
12