Safety Warnings - Makita DLM330 Betriebsanleitung

Intended use
T h e m a c h i n e i s i n t e n d e d f o r l a w n m o w i n g .
Noise
The typical A-weighted noise level determined accord-
i n g t o E N 6 0335-2- 7 7 , IEC 6 2 8 4 1- 4 -3 :
S o u n d p r e s s u r e l e v e l ( L
S o u n d p o w e r l e v e l ( L ) : 8 9.0 d B ( A )
W A
Uncertainty (K) : 3 dB(A)
NOTE: T h e d e c l a r e d n o i s e e m i s s i o n v a l u e ( s ) h a s b e e n
m e a s u r e d i n a c c o r d a n c e w i t h a s t a n d a r d t e s t m e t h o d
and may be used for comparing one tool with another.
NOTE: T h e d e c l a r e d n o i s e e m i s s i o n v a l u e ( s )
may also be used in a preliminary assessment of
e x p o s u r e .
WARNING:
W ear ear protection.
WARNING:
The noise emission during actual
use of the po er tool can di er from the declared
value(s) depending on the ways in which the
tool is used especially what kind of workpiece is
processed.
WARNING:
Be sure to identify safety mea-
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use (taking account of all parts of the operating
cycle such as the times when the tool is switched
o and hen it is running idle in addition to the
trigger time).
Vibration
T h e v i b r a t i o n t o t a l v a l u e ( t r i - a x i a l v e c t o r s u m ) d e t e r -
m i n e d a c c o r d i n g t o E N 6 0335-2- 7 7 , IEC 6 2 8 4 1- 4 -3 :
V i b r a t i o n e m i s s i o n ( a ) : 2.5 m / s
h
Uncertainty (K) : 1.5 m/s
NOTE: T h e d e c l a r e d v i b r a t i o n t o t a l v a l u e ( s ) h a s b e e n
m e a s u r e d i n a c c o r d a n c e w i t h a s t a n d a r d t e s t m e t h o d
and may be used for comparing one tool with another.
NOTE: The declared vibration total value(s) may also
be used in a preliminary assessment of exposure.
WARNING:
The vibration emission during
actual use of the po er tool can di er from the
declared value(s) depending on the ways in which
the tool is used especially what kind of workpiece
is processed.
WARNING:
Be sure to identify safety mea-
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use (taking account of all parts of the operating
cycle such as the times when the tool is switched
o and hen it is running idle in addition to the
trigger time).
EC Declaration of Conformity
For European countries only
The EC declaration of conformity is included as Annex A
t o t h i s i n s t r u c t i o n m a n u a l .
) : 8 2. 4 d B ( A )
p A
2
o r l e s s
2
SAFETY W ARNINGS
General power tool safety warnings
WARNING:
Read all safety warnings, instruc-
tions, illustrations and specifications provided
with this power tool. F a i l u r e t o f o l l o w a l l i n s t r u c t i o n s
listed below may result in electric shock, fire and/or
serious injury.
Save all warnings and instruc-
tions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
( c o r d l e s s ) p o w e r t o o l .
W ork area safety
Keep work area clean and well lit. C l u t t e r e d o r
1.
d a r k a r e a s i n v i t e a c c i d e n t s .
2. Do not operate power tools in explosive atmo-
spheres, such as in the presence of ammable
liquids, gases or dust. P o w e r t o o l s c r e a t e s p a r k s
which may ignite the dust or fumes.
Keep children and bystanders away while operating
3.
a power tool. Distractions can cause you to lose control.
Electrical safety
1. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will
r e d u c e r i s k o f e l e c t r i c s h o c k .
Avoid body contact with earthed or grounded
2.
surfaces, such as pipes, radiators, ranges and
refrigerators. T h e r e i s a n i n c r e a s e d r i s k o f e l e c -
tric shock if your body is earthed or grounded.
3. Do not operate the lawnmower in rain or wet con-
ditions. This may increase the risk of electric shock.
Do not abuse the cord. Never use the cord for
4 .
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges
or moving parts. D a m a g e d o r e n t a n g l e d c o r d s
i n c r e a s e t h e r i s k o f e l e c t r i c s h o c k .
5. W hen operating a power tool outdoors, use an
extension cord suitable for outdoor use. U s e o f
a c o r d s u i t a b l e f o r o u t d o o r u s e r e d u c e s t h e r i s k o f
e l e c t r i c s h o c k .
6 . If operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply. U s e o f a n R CD r e d u c e s
t h e r i s k o f e l e c t r i c s h o c k .
7 . Po er tools can produce electromagnetic fields
(EMF) that are not harmful to the user. H o w e v e r ,
u s e r s o f p a c e m a k e r s a n d o t h e r s i m i l a r m e d i c a l
d e v i c e s s h o u l d c o n t a c t t h e m a k e r o f t h e i r d e v i c e a n d /
o r d o c t o r f o r a d v i c e b e f o r e o p e r a t i n g t h i s p o w e r t o o l .
Personal safety
Stay alert, watch what you are doing and use
1.
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the in uence of drugs, alcohol or med-
ication. A m o m e n t o f i n a t t e n t i o n w h i l e o p e r a t i n g
power tools may result in serious personal injury.
8 ENGLISH