Scheppach 5901201901 Originalbetriebsanleitung Seite 26

• 45° - position angle stop (b) between the saw blade
(6) and rotary table (14).
• Adjust the adjusting screw (28) until the angle between
the saw blade (6) and rotary table (14) is precisely 45°.
• It is not necessary to fix this setting because it is main-
tained by the spring pretension.
• Subsequently check the position of the angle indica-
tor. If necessary loosen the pointer (19) using a Philips
screwdriver, set to position 45° on the angle scale (18)
and re-tighten the retaining screw.
8.6 Mitre cut 0°- 45° and turntable 0° (Fig. 1/2/12)
The crosscut saw can be used to make mitre cuts of 0°
- 45° in relation to the work face.
Important. To make miter cuts (inclined saw head), the
adjustable stop rail (16a) must be fixed at the outer po-
sition.
• Open the set screw (16b) for the adjustable stop rail
(16a) and push the adjustable stop rail outwards.
• The adjustable stop rail (16a) must be fixed far enough
in front of the innermost position that the distance
between the stop rail (16a) and the saw blade (6)
amounts to a maximum of 8 mm.
• Before making a cut, check that the stop rail (16a) and
the saw blade (6) cannot collide.
• Secure the set screw (16b) again.
• Move the machine head (4) to the top position.
• Fix the rotary table (14) in the 0° position.
• Loosen the set screw (22) and use the handle (1) to
angle the machine head (4) to the left, until the pointer
(19) indicates the desired angle measurement on the
scale (18).
• Re-tighten the fixing screw (22).
• Cut as described in section 8.3.
8.7 Mitre cut 0°- 45° and turntable 0°- 45
(Fig. 2/4/13)
The crosscut saw can be used to make mitre cuts to
the left of 0°- 45° in relation to the work face and, at the
same time, 0° - 45° to the left or 0° - 45° to the right in
relation to the stop rail (double mitre cut).
Important. To make miter cuts (inclined saw head), the
adjustable stop rail (16a) must be fixed at the outer po-
sition.
• Open the set screw (16b) for the adjustable stop rail
(16a) and push the adjustable stop rail outwards.
• The adjustable stop rail (16a) must be fixed far enough
in front of the innermost position that the distance
between the stop rail (16a) and the saw blade (6)
amounts to a maximum of 8 mm.
• Before making a cut, check that the stop rail (16a) and
the saw blade (6) cannot collide.
• Secure the set screw (16b) again.
• Move the machine head (4) to its upper position.
• Release the rotary table (14) by loosening the set
screw (26).
• Using the handle (11), set the rotary table (14) to the
desired angle (refer also to point 8.4 in this regard).
• Re-tighten the set screw (26) in order to secure the
rotary table.
26 GB/IE
• Undo the locking screw (22) and use the handle (1)
to tilt the machine head (4) to the left until it coincides
with the required angle value (in this connection see
also section 8.6).
• Re-tighten the fixing screw (22).
• Cut as described under section 8.3.
8.8 Limiting the cutting depth (Fig. 3/14)
• The cutting depth can be infinitely adjusted using the
screw (24). To do this loosen the knurled nut on the
screw (24). Move the stop for the cutting depth limitre
(25) to the outside. Turn the screw (24) in or out to set
the required cutting depth. Then re-tighten the knurled
nut on the screw (24).
• Check the setting by completing a test cut.
8.9 Sawdust bag (Fig. 1)
The saw is equipped with a debris bag (17) for sawdust
and chips.
Squeeze together the metal ring on the dust bag and at-
tach it to the outlet opening in the motor area.
The debris bag (17) can be emptied by means of a zip-
per at the bottom.
8.10 Changing the saw blade (Fig. 15/16/17/18)
Remove the power plug!
Important.
Wear safety gloves when changing the saw blade.
Risk of injury!
• Swing up the machine head (5).
• Undo the screw (e) on the guide bar (37), so that it can
move freely and be pivoted downwards.
• Press the release lever (3). Swing up the saw blade
guard (6) to the point where the recess in the saw
blade guard (6) is above the flange bolt (31).
• Press the saw shaft lock (4) with one hand. With the
other hand insert the allen key (d) in the flange bolt (31).
• Hold the Allen key (d) and slowly close the saw blade
guard until it touches the Allen key.
• Firmly press the saw shaft lock (4) and slowly rotate the
flange bolt (31) in clockwise direction. The saw shaft lock
(4) engages after no more than one rotation.
• Now, using a little more force, slacken the flange bolt
(31) in the clockwise direction.
• Turn the flange screw (31) right out and remove the
external flange (32).
• Take the blade (7) off the inner flange (38) and pull
out downwards.
• Carefully clean the flange screw (31), outer flange (32)
and inner flange (38).
• Fit and fasten the new saw blade (7) in reverse order.
• Important! The cutting angle of the teeth, in other words
the direction of rotation of the saw blade (7) must co-
incide with the direction of the arrow on the housing.
• Move the guide bar (37) into position and tighten the
screw (e) again.
• Before continuing your work make sure that all safety
devices are in good working condition.
• Important! Every time that you change the saw blade
(7), check to see that it spins freely in the table insert
(11) in both perpendicular and 45° angle settings.