Specifications; Battery Removal/Installation - Hitachi DV 14DSFL Bedienungsanleitung

WARNING
If a conductive foreign matter enters in the terminal of lithium
ion battery, the battery may be shorted, causing fi re. When
storing the lithium ion battery, obey surely the rules of
following contents.

SPECIFICATIONS

POWER TOOL
Model
No-load speed (Low/High)
No-load impact rate (Low/High)
Brick
(Depth 30 mm)
Wood
Drilling
(Thickness 18 mm)
Metal
Capacity
(Thickness 1.6 mm)
Machine screw
Driving
Wood screw
Rechargeable battery
Weight
CHARGER
Model
Charging voltage
Weight
STANDARD ACCESSORIES
1 Plus driver bit (No. 2) .............................. 1
2 Charger (UC18YGSL) ............................ 1
DV18DSFL 3 Battery (BSL1815) .................................. 2
4 Plastic case ............................................ 1
5 Battery cover .......................................... 1
1 Plus driver bit (No. 2) .............................. 1
2 Charger (UC18YGSL) ............................ 1
DV14DSFL 3 Battery (BSL1415) .................................. 2
4 Plastic case ............................................ 1
5 Battery cover .......................................... 1
Standard accessories are subject to change without notice.
OPTIONAL ACCESSORIES (sold separately)
1. Battery (BSL1415)
(For DV14DSFL)
2. Battery (BSL1815)
(For DV18DSFL)
Optional accessories are subject to change without notice.
DV14DSFL
0 – 400 / 0 – 1500 min
0 – 5600 / 0 – 21000 min
13 mm
32 mm
13 mm
8 mm (diameter) × 50 mm (length)
(Requires a pilot hole)
BSL1415: Li-ion 14.4 V (1.5 Ah 4 cells)
1.6 kg
UC18YGSL
14.4 – 18 V
0.4 kg
○ Do not place conductive debris, nail and wires such
as iron wire and copper wire in the storage case.
○ To prevent shorting from occurring, load the battery
in the tool or insert securely the battery cover for
storing until the ventilator is not seen (See Fig. 1).
-1
-1
6 mm
BSL1815: Li-ion 18 V (1.5 Ah 5 cells)
APPLICATIONS
○ Drilling of brick and concrete block, etc.
○ Driving and removing of machine screws, wood screws,
tapping screws, etc.
○ Drilling of various metals.
○ Drilling of various woods.

BATTERY REMOVAL/INSTALLATION

1. Battery removal
Hold the handle tightly and push the battery latch (2 pcs.)
to remove the battery (see Figs. 1 and 2).
CAUTION
Never short-circuit the battery.
2. Battery installation
Insert the battery while observing its polarities (see
Fig. 2).
CHARGING
Before using the power tool, charge the battery as follows.
1. Connect the charger's power cord to the receptacle.
When connecting
a receptacle, the pilot lamp will blink in red
(At 1-second intervals).
2. Insert the battery into the charger.
Firmly insert the battery into the charger as shown in Fig.
3, 4.
3. Charging
When inserting a battery in the charger, the pilot lamp will
light up continuously in red.
When the battery becomes fully recharged, the
pilot lamp will blink in red (At 1-second intervals).
(See Table 1)
(1) Pilot lamp indication
The indications of the pilot lamp will be as shown in
Table 1, according to the condition of the charger or the
rechargeable battery.
English
DV18DSFL
0 – 400 / 0 – 1500 min
0 – 5600 / 0 – 21000 min
13 mm
38 mm
13 mm
6 mm
8 mm (diameter) × 75 mm (length)
(Requires a pilot hole)
1.7 kg
the plug of the charger
-1
-1
to
9