Waldorf MicroWave II Bedienungsanleitung Seite 112

179-206 IDATA see 3.3
207-234 IDATA see 3.3
235-262 IDATA see 3.3
263 XSUM (BB+NN+DATA)&7Fh Checksum
264 EOX F7h
------------------------------------------------------
******************************************************
2.23 MULP
******************************************************
MULP 20h Multi Parameter Change
Upon reception of a valid Multi Parameter Change dump,
the specified parameter will change its value
immediately according to the given value. In Sound
Mode, all MULP messages will be ignored. The location
is given in one byte with following conventions:
LL Location
------------------------------------------------
20h Multi Edit Buffer
01h..07h Multi Mode Instrument 1..8 buffer
------------------------------------------------
The Parameter index is given in one byte:
PP Parameter index
------------------------------------------------
00..1Fh Parameters with indices 0 to 31
------------------------------------------------
See 3.2 for a detailed list of Multi parameters and
indices, or 3.3 for a detailed list of Instrument
parameters and indices.
The actual Format is:
Index Label Value
------------------------------------------------------
0 EXC F0h
1 IDW 3Eh
2 IDE 0Eh
3 DEV
4 IDM 21h
5 LL see above Location
7 PP see above Parameter index
8 XX see 3.2/3.3
9 EOX F7h
------------------------------------------------------
******************************************************
2.31 WAVR
******************************************************
WAVR 02h Wave Request
Upon reception of a valid wave request the MW2 will
dump the selected Wave. The location is given in two
bytes with following conventions:
HH LL Location
------------------------------------------------
00 00 .. 00 7F ROM Waves 000..127
01 00 .. 01 7F ROM Waves 128..255
01 00 .. 01 2B ROM Waves 256..299
07 68 .. 07 7F User Waves 1000..1023
08 00 .. 08 7F User Waves 1024..10151
09 00 .. 09 61 User Waves 1152..1249
------------------------------------------------
So the full format of a WAVR Request is:
Index Label Value
------------------------------------------------------
0 EXC F0h
1 IDW 3Eh
2 IDE 0Eh
3 DEV
4 IDM 02h
5 HH see Text
6 LL see Text
7 XSUM (HH+LL)&7Fh
8 EOX F7h
112
Instrument #6 data
Instrument #7 data
Instrument #8 data
End of SysEx
Description
Marks Start of SysEx
Waldorf Electronics
GmbH ID
Microwave 2 ID
Device ID
here MULP (Sound
Parameter change)
New Parameter value
End of Exclusive
Description
Marks Start of SysEx
Waldorf Electronics
GmbH ID
Microwave 2 ID
Device ID
here WAVR (Wave
request)
Location
Location
Checksum
End of SysEx
------------------------------------------------------
******************************************************
2.32 WAVD
******************************************************
WAVD 12h Wave Dump
A wave dump is used to transfer wave data from and to
the Microwave 2. The location is given in two bytes
with following conventions:
HH LL Location
------------------------------------------------
00 00 .. 00 7F ROM Waves 000..127
01 00 .. 01 7F ROM Waves 128..255
02 00 .. 02 2B ROM Waves 256..299
07 68 .. 07 7F User Waves 1000..1023
08 00 .. 08 7F User Waves 1024..10151
09 00 .. 09 61 User Waves 1152..1249
------------------------------------------------
So the full format of a WAVD Dump is:
Index Label Value
------------------------------------------------------
0 EXC F0h
1 IDW 3Eh
2 IDE 0Eh
3 DEV
4 IDM 12h
5 HH see above Location
6 LL see above Location
7-134 WDATA see 3.4
135 XSUM (HH+LL+WDATA)&7Fh Checksum
136 EOX F7h
------------------------------------------------------
******************************************************
2.41 WCTR
******************************************************
WCTR 03h Wave Control Table Request
Upon reception of a valid wave control table request,
the MW2 will dump the selected Table. The location is
given in two bytes with following conventions:
HH LL Location
-----------------------------------------------------
00 00 .. 00 7F Control Table of Wavetables 001..128
-----------------------------------------------------
Note that some Wavetables are generated
algorithmically and have no control table, an attempt
to request such a table will fail.
The full format of a WCTR Request is:
Index Label Value
------------------------------------------------------
0 EXC F0h
1 IDW 3Eh
2 IDE 0Eh
3 DEV
4 IDM 03h
5 HH see Text
6 LL see Text
7 XSUM (HH+LL)&7Fh
8 EOX F7h
------------------------------------------------------
******************************************************
2.42 WCTD
******************************************************
**************
WAVD 13h Wave ControlDump
A Control Table dump is used to transfer Wavetable
Control Table data from and to the Microwave 2. The
location is given in two bytes with following
conventions:
Bedienhandbuch MicroWave II • MicroWave XT • XTk
Description
Marks Start of SysEx
Waldorf Electronics
GmbH ID
Microwave 2 ID
Device ID
here WAVD (Wave
Dump)
Wave data
End of SysEx
Description
Marks Start of SysEx
Waldorf Electronics
GmbH ID
Microwave 2 ID
Device ID
here WCTR (Wavetable
request)
Location
Location
Checksum
End of SysEx