DeWalt DWE4051 Originalanweisungen Seite 43

MOUNTING AND REMOVING (TYPE 27)
ONE-TOUCH GUARD (FIG. 2A)
NOTE: If your grinder is supplied with a keyless
One-Touch guard, ensure the screw and spring are
fitted correctly before mounting the guard
1. Press the guard release lever (h).
2. While holding the guard release lever open, align
the lugs (i) on the guard with the slots on the
gear case (j).
3. Keeping the guard release lever open, push the
guard down until the lugs engage then rotate
them into the groove on the gear case hub.
Release the guard release lever.
4. With the spindle facing the operator, rotate
the guard clockwise into the desired working
position. The guard body should be positioned
between the spindle and the operator to provide
maximum operator protection.
5. For easy adjustment, the guard can be rotated
in the clockwise direction. NOTE: The guard
release lever should snap into one of the
alignment holes (k) on the guard collar. This
ensures that the guard is secure. The guard
can be repositioned the opposite direction by
depressing the guard release lever.
6. To remove the guard, follow steps 1–3 of these
instructions in reverse.
GUARD WITH FIXING SCREW (FIG. 2B)
1. Place the angle grinder on a table, spindle
up.
2. Align the lugs (i) with the notches (j).
3. Press the guard (f) down and rotate it to the
required position.
4. Securely tighten the screw (m).
5. To remove the guard, slacken the screw.
CAUTION: If the guard cannot be
tightened by the adjusting screw, do
not use the tool. To reduce the risk of
personal injury, take the tool and guard
to a service center to repair or replace
the guard.
MOUNTING CLOSED (TYPE 1) GUARD
NOTE: If present, the One-Touch guard lever, screw,
and spring should be removed before attempting to
mount the Type 1 guard.
1. Open the guard latch. Align the lugs (i) on the
guard with the slots (j) on the gear case.
2. Push the guard down until the guard lug
engages and rotates freely in the groove on the
gear case hub.
3. Rotate guard into desired working position.
The guard body should be positioned between
the spindle and the operator to provide
maximum operator protection.
4. Close the guard latch to secure the guard on
the gear case cover. You should be unable to
rotate the guard by hand when the latch is in
closed position. If rotation is possible, tighten
the adjusting screw with the clamp lever in the
closed position. Do not operate grinder with a
loose guard or clamp lever in open position.
5. To remove the guard, open the guard latch,
rotate the guard so that the arrows are aligned
and pull up on the guard.
NOTE: If, after a period of time, the guard becomes
loose, tighten the adjusting screw with the clamp
lever in the closed position.
NOTICE: Do not tighten adjusting
screw with clamp lever in open position.
Undetectable damage to guard or
mounting hub may result.
CAUTION: If the guard cannot be
tightened by the adjusting screw, do
not use the tool. To reduce the risk of
personal injury, take the tool and guard
to a service center to repair or replace
the guard.
Fitting and Removing a Grinding or
(b)
Cutting Disc (fi g. 1, 4, 5)
WARNING: Do not use a damaged
disc.
1. Place the tool on a table, guard up.
2. Fit the backing flange (d) correctly onto the
spindle (b) (fig. 4).
3. Place the disc (n) on the backing flange (d).
When fitting a disc with a raised centre, make
sure that the raised centre (l) is facing the
backing flange (d).
4. Screw the threaded clamp nut (e) onto the
spindle (b) (fig. 5):
a. The ring on the threaded clamp nut (e) must
face towards the disc when fitting a grinding
disc (fig. 5A);
b. The ring on the threaded clamp nut (e) must
face away from the disc when fitting a cutting
disc (fig. 5B).
5. Press the spindle lock button (a) and rotate the
spindle (b) until it locks in position.
6. Tighten the threaded clamp nut (e) with the hex
key provided or a two pin spanner.
EN GL IS H
41