Safety Information - Parkside PSKO 24 A1 Originalbetriebsanleitung

Please observe that our equipment was not designed with the
intention of use for commercial or industrial purposes. We as-
sume no guarantee if the equipment is used in commercial or
industrial applications, or for equivalent work.

6. Safety information

m Attention!
The following basic safety measures must be observed when
using power tools for protection against electric shock, and the
risk of injury and fire. Read all these notices before using the
electric tool and store the safety instructions well for later refer-
ence.
Safe work
1. Keep the work area orderly
- Disorder in the work area can lead to accidents.
2. Take environmental influences into account
- Do not expose power tools to rain.
- Do not use electric tools in a damp or wet environment.
There is a risk of electric shock!
- Make sure that the work area is well-illuminated.
- Do not use power tools where there is a risk of fire or
explosion.
3. Protect yourself from electric shock
- Avoid physical contact with earthed parts (e. g. pipes,
radiators, electric ranges, cooling units).
4. Keep away from children!
- Do not allow other persons to touch the equipment or
cable, keep them away from your work area.
5. Securely store unused electric tools
- Unused power tools should be stored in a dry, elevated
or closed location out of the reach of children.
6. Do not overload your power tool
- They work better and more safely in the specified output
range.
7. Dress properly
- Do not wear wide clothing or jewellery, which can
become entangled in moving parts.
- Rubber gloves and anti-slip footwear are recommended
when working outdoors.
- Tie long hair back in a hair net.
8. Do not use the cable for purposes for which it is not
intended
- Do not use the cable to pull the plug out of the outlet.
Protect the cable from heat, oil and sharp edges.
9. Take care of your tools
- Keep your compressor clean in order to work well and
safely.
- Follow the maintenance instructions.
- Check the connection cable of the power tool regularly
and have it replaced by a recognised specialist when
damaged.
- Check extension cables regularly and replace them
when damaged.
10. Pull the connector out of the socket
- When the electric tool is not in use or prior to
maintenance and when replacing tools such as saw
blades, bits, milling heads.
11. Avoid inadvertent starting
- Make sure that the switch is switched off when plugging
the plug into an outlet.
12. Use extension cables for outdoors
- Only use approved and appropriately identified
extension cables for use outdoors.
- Only use cable reels in the unrolled state.
13. Always remain attentive
- Pay attention to what you are doing. Remain sensible
when working. Do not use the power tool when you are
distracted.
14. Check the power tool for potential damage
- Protective devices or other parts with minor damage
must be carefully inspected to ensure that they function
correctly and as intended prior to continued use of the
electric tool.
- Check whether the moving parts function faultlessly and
do not jam or whether parts are damaged. All parts
must be correctly mounted and all conditions must be
fulfilled to ensure fault-free operation of the electric tool.
- Damaged protective devices and parts must be properly
repaired or replaced by a recognised workshop, insofar
as nothing different is specified in the operating manual.
- Damaged switches must be replaced at a customer
service workshop.
- Do not use any faulty or damaged connection cables.
- Do not use any electric tool on which the switch cannot
be switched on and off.
15. Have your power tool repaired by a qualified electrician
- This electric tool conforms to the applicable safety
regulations. Repairs may only be performed by an
electrician using original spare parts. Otherwise
accidents can occur.
16. Attention!
- For your own safety, only use accessories and additional
equipment that are indicated in the operating manual
or have been recommended or indicated by the
manufacturer. Use of other tools or accessories that
those recommended in the operating manual or in the
catalogue could represent a personal danger to you.
17. Noise
- Wear hearing protection when using the compressor.
18. Replacing the connection line
- If the connection line is damaged, it must be replaced
by the manufacturer or an electrician to avoid danger.
There is a risk of electric shock.
19. Filling tyres
- Directly after inflating tyres, check the pressure with
a suitable pressure gauge, for example at your filling
station.
20. Street-legal compressors in construction site operation
- Ensure that all hoses and fixtures are suitable for
the maximum permissible working pressure of the
compressor.
21. Set-up location
- Only set up the compressor on a flat surface.
22. In case of pressures above 7 bar, it is recommended
to equip supply hoses with a safety cable (e. g. a wire
rope).
GB 35