Cleaning And Maintenance; Storage; Electrical Connection - Parkside PBTS 370 A1 Originalbetriebsanleitung

11.6 Sanding outside (convex) curves (fig. 19)
Always sand convex curves using the sanding disc by guiding
the workpiece (W) from the left side to the centre of the sand-
ing disc.
• Hold the workpiece firmly. Watch your fingers! Danger of
injury!
• Press the workpiece firmly against the sanding disc moving it
from the left to the centre of the sanding disc.
Warning:Never attempt to sand concave curves at the right
side of the sanding disc! The workpiece may be ejected! Dan-
ger of injury!

12. Cleaning and maintenance

Warning! Pull out the mains plug before carrying out any ad-
justments, maintenance or repair work!
12.1 General maintenance tasks
Wipe swarf and dust off the machine from time to time with a
cloth. Oil the rotating parts once monthly to extend the life of
the tool. Do not oil the motor.
Do not use corrosive agents for cleaning the plastic.
12.2 General maintenance information
After using your sander, clean it completely. Regularly lubricate
all moving parts.
12.3 Cleaning
Dust can collect in the belt and disc sander. Check regularly
(preferably after each use) and remove dust, e. g. by blowing
away or carefully with compressed air.
12.4 Service information
With this product, it is necessary to note that the following
parts are subject to natural or usage-related wear, or that the
following parts are required as consumables.
Wearing parts*: sanding tools, toothed belt
* not included in the scope of delivery!
12.5 Available accessories
• Sanding belt L 915 x W 100 mm, 3 units respectively:
K 240 − article number: 7903306602
K 120 − article number: 88000212
K 180 − article number: 88000221
K 80 − article number: 88000211
• Sanding paper Ø 150 mm, 10 units respectively:
K 80 − article number: 88000208
K 120 − article number: 88000209
K 180 − article number: 88000220
K 240 − article number: 7903306601
• Sanding set 12 pieces − article number: 7903302601
Comprising:
3 x sanding paper grain size 80/120/180 respectively
1 x sanding paper grain size 80/120/180 respectively
• Protective goggles − article number: 7909601701

13. Storage

Store the device and its accessories in a dark, dry and frost-
free place that is inaccessible to children. The optimum storage
temperature lies between 5 and 30 ˚C.
Cover the device in stationary use after work to protect it from
dust or moisture.
Store the device in portable use in the original packaging after
work.
Store the operating manual with the power tool.

14. Electrical connection

The electrical motor installed is connected and ready for op-
eration. The connection complies with the applicable VDE and
DIN provisions. The customer's mains connection as well as
the extension cable used must also comply with these regula-
tions.
14.1 Damaged electrical connection cable
The insulation on electrical connection cables is often dam-
aged.
This may have the following causes:
• Pressure points, where connection cables are passed
through windows or doors.
• Kinks where the connection cable has been improperly fas-
tened or routed.
• Places where the connection cables have been cut due to
being driven over.
• Insulation damage due to being ripped out of the wall out-
let.
• Cracks due to the insulation ageing.
Such damaged electrical connection cables must not be used
and are life-threatening due to the insulation damage.
Check the electrical connection cables for damage regularly.
Ensure that the device is disconnected from electrical power
when checking for damage.
Electrical connection cables must comply with the applicable
VDE and DIN provisions. Only use connection cables of the
same designation.
The printing of the type designation on the connection cable
is mandatory.
Safety information for replacing damaged or de-
fective mains connection cables
Type Y
If it is necessary to replace the connection cable, this must
be done by the manufacturer or their representative to avoid
safety hazards.
14.2 AC motor
• The mains voltage must be 230−240 V∼ .
• Extension cables up to 25 m long must have a cross-section
of 1.5 mm2.
Connections and repair work on the electrical equipment may
only be carried out by electricians.
GB/MT 41