Incoming Calls; Technical Data - Clatronic ar 736 Bedienungsanleitung

5. To terminate the call please press the B /

Incoming Calls

In the case of incoming calls a ringing tone is heard from the
loudspeakers, and if the caller has a CLIP „Calling Line Iden-
tifi cation Presentation"-capable telephone, the caller's number
appears in the display of the car radio. Otherwise „PHONE IN"
appears in the display.
1. To accept an incoming call, press the M /
button (5) to confi rm. You will now hear the caller through
the loudspeakers of your car.
2. To terminate the call please press the B /
Note:
• You can transfer the call back to your mobile telephone. In
order to do so, keep the M /
pressed („TRANSFER
car radio activates the MUTE function. If this button is held
down again, the call is transferred back to the car radio.
• In order to reject an incoming call press the B /
button (6).

Technical data

General
Supply voltage ...............................................................DC 12 V
Power consumption ......................................................7 A max.
Power ............................................................... 4 x 60 W PMPO
FM band
Frequency range ...................................87,5 MHz to 108,0 MHz
Effective sensitivity ............................................................15 dB
I.F. frequency...............................................................10,7 MHz
CD player
System............................................................CD Audio System
Suitable CDs.................................CD/CD-R/CD-RW/MP3 disks
Playable bit rates .................................................32 - 320 kBit/s
Number of quantising bits................................................... 1 bit.
Signal format ............................... Sampling frequency 44,1 kHz
Signal-to-noise ratio..............................................50 dB (1 kHz)
Number of channels .......................................2 stereo channels
Housing dimensions ........................ 178 x 50 x 157 (W x H x D)
This device has been tested according to all relevant current
CE guidelines, such as electromagnetic compatibility and low
voltage directives, and has been constructed in accordance with
the latest safety regulations.
Subject to technical changes without prior notice!
05-AR 736 CD_MP3_NEU 77
CLEAR button (6).
TRANSFER
CLEAR button (6).
TRANSFER button (5)
" appears in the display). The
CLEAR
Troubleshooting
Before going through the checklist please make all the
connections fi rst. If you still have questions after going through
the checklist, please consult your local customer service
representative.
Fault Symptoms Cause
Whistling sound from Feedback
the loudspeakers.
CDs are drawn only The transport screws
half way into the CD have not been
tray. removed.
„READ ERR" is shown The CD is inserted the
in the display. wrong way round.
CD cannot be selected There is no CD
using the MODE inserted.
button.
The CD does not play The volume control is
back after being inser- set too low.
ted into the device. The device has
not been correctly
connected.
CD works intermittently The surface of the road
(dropouts). is uneven.
The device is not fi rmly
installed.
The CD is damaged.
The CD is dirty.
The device may have
been installed in the
vehicle at the wrong
angle.
No function. The ignition is switched
off.
One or more fuses
have blown.
Device cannot be Incorrect connection
switched on or off via (each car manufacturer
the ignition. wires the ISO con-
nection in the vehicle
differently).
The device does not The microcomputer
work correctly (EJECT, has been interfered
LOAD, PLAY). with by electromagne-
tic fi elds.
No radio reception. The antenna cable is
not connected.
Solution
Do not set the volume
too high.
Remove the transport
screws.
Insert the CD right way
round.
Insert a CD.
Turn up the volume.
Check the +12V and
earth connection.
Wait until the road
becomes smoother
before playing the CD.
Install the device fi rmly.
Ensure that the rear at-
tachment is used if the
vehicle does not have
any suitable retainer
for the rear section of
the device.
Try another CD. If this
works correctly, the
fi rst CD is probably
damaged.
Clean the CD.
Please note that a
maximum inclination
of 20° degrees should
not be exceeded!
Turn the ignition key to
„ON" or „ACC".
Replace the fuse by
another 15 A fuse.
Please contact your
car workshop or a
vehicle specialist for
connection adapters
may specifi cally for
your model.
Remove the CD and
reinsert it.
Switch the device off
and on again.
Insert the antenna
cable fi rmly into the
antenna socket of the
device.
77
18.09.2006, 11:02:28 Uhr