Safety Advice Relating Specifically To Bench Grinders - Scheppach BG 150 Originalanleitung

17. Avoid unintentionally starting up the device.
• Check that the switch is set to OFF on the device
when the mains plug is inserted into the mains
socket.
18. Using an extension lead for working outdoors.
• When working outside, always use an approved and
appropriately labelled extension lead.
19. Remain alert.
• Watch what you are doing. Proceed with caution. Do not
use electrical power tools if you cannot concentrate.
20. Check the electrical power tool for damage.
• Before the electrical power tool is used, carefully
check the safety equipment and any slightly dam-
aged parts to see that they are still working properly.
• Check that all moving parts on the tool are work-
ing properly, can move freely and are not damaged.
All parts must be correctly attached and fulfil all the
requirements necessary to allow the electrical power
tool to operate properly.
• Damaged safety equipment and components must
be properly repaired or replaced at a competent
electrical equipment repair centre unless otherwise
indicated in the operating instructions.
• Damaged switches must be replaced at a Customer
Service Centre.
• Never use an electrical power tool that cannot be
switched on and off properly.
21. CAUTION!
• The use of inserted tools and accessories other than
those recommended by the manufacturer could lead
to you being injured.
22. Have your electrical power tool repaired at an
electrical equipment repair specialist.
• This electrical power tool complies with the relevant
safety regulations. Repairs may only be carried out
by a specialist electrical repair centre using original
spare parts, otherwise injury could occur to the user.
m Safety advice relating specifically
to bench grinders
• Do not touch the mains lead if it becomes damaged
or cut through while you are using the device. Pull
the plug out of the mains socket immediately and
have the device repaired by a suitably qualified per-
son or at your service centre.
• Do not operate the device if it is damp and do not
use it in a damp environment.
• If you use the device outdoors, always connect
it through a residual current device (RCD) with a
maximum trip current of 30 mA.If using an extension
lead, always use one that is approved for outdoor
use.
• If a dangerous situation arises, pull the mains plug
immediately out of the mains socket.
• Always work with the mains lead leading away from
the rear of the device.
• Dang er of fire from flying sparks !
Grinding metal creates flying sparks. For this reason,
always make sure that nobody is placed in any danger
and that there are no inflammable materials near the
working area.
16 GB
mWarning! Noxious fumes!
Working with harmful / noxious dusts represents a risk
to the health of the person operating the device and to
anyone near the work area.
Wear protective glasses, hearing protection,
•
dust protection mask and protective gloves.
• Dang er of burns! The workpiece
gets hot during grinding. Never touch the part you
are grinding. Allow the workpiece to cool sufficiently
first. When grinding for longer periods, stop grind-
ing from time to time and allow the workpiece to cool
before continuing. Do not operate the device for
continuous periods exceeding 30 minutes.
• The double grinding machine is intended for dry
grinding of the surfaces of metal objects. The device
may only be used for dry grinding.
• Do not grind materials containing asbestos. Asbes-
tos is a known carcinogen.
• Do not use damaged grinding wheels.
• Only use grinding wheels with details that corr
spond with those given on the device ratin plate. The
circumferential speed should be equal to or greater
than the value given on the device rating plate.
• Adjust the eye guard mounts (spark deflectors)
and the eye guards periodically so that wear on the
grinding wheels can be evened out. Keep the gap as
small as possible.
• Avoid contact with the moving grinding wheel.
• Never leave the device working unattended.
• Never use the device for a purpose for which it was
not intended.
• Before you insert the mains plug into the socket, al-
ways check that the device is switched off.
• Always switch the device on before bringing the
workpiece into contact with the grinding wheel. After
grinding, lift off the workpiece before switching the
device off.
• Hold the workpiece firmly with both hands at all
times when working.
• Always keep proper footing and balance.
• After you have finished grinding metal, allow the
grinding wheel(s) to come to a standstill.
• When taking a break from your work, before carrying
out any tasks on the device itself and when you are
not using the device, always pull the mains plug out
of the mains socket.
• Handle the device carefully and treat it with respect.
Always keep the device clean, dry and free of oil or
grease.
• Remain alert at all times! Always watch what you
are doing and proceed with caution. Do not use the
device if you cannot concentrate or you are feeling
unwell.
• Store grinding wheels in such a way that they are
not subject to mechanical loads or damaging envi-
ronmental influences.
• Do not use damaged or unshaped wheels.
• The adjustment of the spark guard shall be made fre-
quently, so as to compensate the wear of the wheel,
keeping the distance between the guard and the wheel
as small as possible, and no greater than 2 mm.