Inhaltsverzeichnis
Werbung
6.1 Record Programming
Variant 1
Possible messages in the dialogue line
If the "Remaining time" is negative (–) and highlighted in red,
then a cassette of insufficient playing time has been loaded,
or the sum of all TIMER recordings is too large.
If the message » Record period « appears instead of
» Remaining playing time, « then...
... no cassette is loaded;
... the cassette is protected against new recording and will be
automatically ejected.
... the playing time of the cassette was not recognized.
If a red line with the message » Record Timer Overlap «
appears (the corresponding TIMER positions are highlighted
in red), then the recording times of the TIMER positions over-
lap.
In this case, change the data of one TIMER position by
"
pressing the
(green) button and selecting the timer
W
Q
position with the
or
button.
E
R
Select the data to be changed with the
or
button,
enter the new data, and confirm the data lines step by step
O
with the
button.
When you are still in the "Record Programming" mode, the
message "Record beginning soon" will appear ten minutes
before the beginning of the recording.
If the message » Record start time has passed « appears,
then you must immediately exit the record programming
mode so that the recorder can start recording.
In order to do so, press the
(TIMER) button.
©
Modifying individual data items of a TIMER posi-
tion
Select the "Info" menu by pressing the
button.
ø
Select the "Record Programming" menu by pressing the
"
numeric button
1
, and then press the
(green) button.
Select the respective TIMER position by pressing the
W
or
Q
button.
E
Select the data item to be modified by pressing the
or
R
button, enter the new data with the numeric buttons
1
0
...
, and confirm the data lines step by step with the
O
button.
Clearing TIMER positions
Select the "Info" menu by pressing the
button.
ø
Select the "Record Programming" menu by pressing the
1
"
numeric button
, and then press the
(green) button.
W
Q
Select the TIMER position to be cleared with the
or
button and clear it by pressing the
ƒ
button.
The TIMER position is cleared and can be programmed again.
Interrupting the record stand-by mode of the
recorder
If you have programmed TIMER positions but wish to use the
recorder while it is in record stand-by mode, or you want to
terminate the TIMER recording, then:
>
press the
button on the recorder, the cassette is automa-
tically ejected,
or
press the
(TIMER) button.
©
The TIMER data disappears from the display of the recorder
and the TIMER display flashes.
The record stand-by mode of the recorder is now inter-
rupted.
Now select the desired function.
Reactivating the record stand-by mode of the
recorder
Insert a cassette with sufficient playing time, wait until the
tape measurement is completed, and then press the
©
(TIMER) button.
The remaining playing time appears briefly in the display of
the recorder.
The recorder is in ready mode again, and the TIMER accord-
ings are made at the set times.
The cassette number also appears briefly in the display.
If » CASS N
O
- --- « appears in the display of the recorder
instead of the cassette number, you must enter the number if
you want to archive the cassette.
Enter the cassette number as a three-place number with the
1
0
O
numeric buttons
...
and confirm with the
button.
The recorder is once again in the record stand-by mode and
the TIMER recordings will be made at the programmed times.
6.2 Record Programming
with ShowView
Programming with the ShowView System,
Variant 2
You must perform the settings described in chapter so that
your recorder is able to evaluate the ShowView data.
Programming example
Press these buttons on the
remote control
You will see this on your TV screen
1. Starting programming
¶
- - - - -
––––
2. Entering the ShowView number for
the desired broadcast
1
0
...
7654 -
––––
Preparation
Insert a cassette with sufficient playing time; note erase pro-
tection.
When » CASS N
O
- --- « appears in the recorder´s display, enter
the number of the cassette as a three-place digit with the
1
0
O
numeric buttons
...
and confirm with the
button.
The cassette number must only be entered if you want to use
the archive system.
Check the time and date.
Explanations
The remote control is ready for entering
data.
1
2
3
4
5
6
7
8
9
0
SAT
Enter the same ShowView code as the
one given in your TV programme guide.
If you want to record daily programmes
– or weekly programmes – which are
1
2
3
broadcast at the same time, press the
button once or twice.
å
4
5
6
The "daily" function cannot be used
7
8
9
for recording on Saturday and Sun-
day.
0
SAT
Press the
w
button if you want to
record in the long-play mode.
Werbung
Inhaltsverzeichnis
