Technical Data; Before Starting The Equipment; Attachment And Operation; Mains Connection - Scheppach 5806105901 Original Bedienungsanleitung

Operating pressure vessels
• You must keep your pressure vessel in good work-
ing order, operate the vessel correctly, monitor the
vessel, carry out necessary maintenance and re-
pair work immediately and meet the relevant safety
precautions.
• The supervisory authority may enforce essential
control measures in individual cases.
• A pressure vessel is not allowed to be used if it
has faults or deficiencies that can endanger work-
ers or third parties.
• Check the pressure vessel for signs of rust and
damage each time before using. Do not use the
compressor with a damaged or rusty pressure ves-
sel. If you discover any damage, then please con-
tact the customer service workshop.
Do not lose these safety instructions

6. Technical data

Mains connection

Motor rating
Operating mode
Compressor speed
Pressure vessel capacity (in liters)
Operating pressure
Theoretical intake capacity (l/min)
Sound power level L
WA
Uncertainty K
WA
Protection type
Weight of the unit in kg
Oil (15W 40) l
Max. altitude
(above mean sea level)
The noise emission values were measured in ac-
cordance with EN ISO 3744.
Wear hearing protection.
The effects of noise can cause a loss of hearing.

7. Before starting the equipment

Before you connect the equipment to the mains sup-
ply make sure that the data on the rating plate are
identical to the mains data.
Prior to initial commissioning, remove the trans-
•
port plug (B) and fill the crank housing with oil as
described in item 8.4.
• Check the equipment for damage which may have
occurred in transit. Report any damage immedi-
ately to the transport company which was used to
deliver the compressor.
22 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
• Install the compressor near the point of consump-
• Avoid long air lines and supply lines (extension
• Make sure that the intake air is dry and dustfree.
• Do not install the compressor in a damp or wet
• The compressor may only be used in suitable
• The compressor is designed to be used in dry
• The oil level in the compressor pump has to be

8. Attachment and operation

m Important!
230V / 50Hz
You must fully assemble the appliance before using it
2200 W
for the first time!
S1
You will require the following tools for assembly and
2850 min installation: 2 x open-ended wrench size 19 mm (not
-1
included)
100
You will require the following tools for assembly and
approx. 8
installation: 2 x open-ended wrench size 14 mm (not
bar
included)
approx. 412
97 dB(A)
8.1 Fitting the wheels (Fig. 5)
• Fit the supplied wheels (11) as shown.
2,03 dB
IP20
8.2 Fitting the supporting foot (2x) (Fig. 6)
approx. 52,7
• Fit the supplied supporting foot (2x) as shown.
approx. 0,25
8.3 Fitting the air filter (2x) (Fig. 7, 8)
1000 m
• Remove the transportation stop (A) and screw the
8.4 Changing the transportation cover (B) (Fig. 9,
10)
•
•
8.5 Mains connection
• The compressor is equipped with a mains cable
• Before you use the machine, make sure that the
tion.
cables).
room.
rooms (with good ventilation and an ambient tem-
perature from +5 °C to 40 °C). There must be no
dust, acids, vapors, explosive gases or inflamma-
ble gases in the room.
rooms. It is prohibited to use the compressor in
areas where work is conducted with sprayed water.
checked before putting the equipment into opera-
tion.
air filter (14) to the equipment.
Remove the transport lid (B) of the oil filling open-
ing (19).
Fill the included compressor oil into the crank
housing and insert the included oil sealing plug
(15) into the oil filling opening (19).
with shock-proof plug. This can be connected to
any 230-240V ~ 50 Hz shock-proof socket.
mains voltage is the same as the operating voltage
(see the rating plate).