Electrical Connection; Accessories - Scheppach dms 1200 Vario Originalanleitung

• Turn the workpiece by hand to check if it rests se-
cured.
Marking of the workpiece, figure 17
Sometimes the workpiece has to be taken out before it has
been completed. It is advantageous to mark the workpiece
and the driver with a pencil first.
When placing the workpiece back in the machine, match
the marks on the workpiece and the driver.
By means of the spindle locking bolt (E1), you can lock
the spindle.
12 screenings with respectively 30° are possible by mark-
ing out.
Specialized literature
Specialized shops offer appropriate specialized literature
about wood turning. They can be a great help for begin-
ners in their work as well as a source of ideas for experts.
m Electrical connection
The installed electric motor is completely wired ready for
operation.
The customer's connection to the power supply system,
and any extension cables that may be used, must conform
with local regulations.
Important remark:
The motor is automatically switched off in the event of an
overload. The motor can be switched on again after a cool-
ing down period that can vary.
Defective electrical connection cables
Electrical connection cables often suffer insulation dam-
age.
Possible causes are:
• Pinch points when connection cables are run through
window or door gaps.
• Kinks resulting from incorrect attachment or laying of
the connection cable.
• Cuts resulting from running over the connecting ca-
ble.
• Insulation damage resulting from forcefully pulling out
of the wall socket.
• Cracks through aging of insulation.
Such defective electrical connection cables must not be
used as the insulation damage makes them extremely haz-
ardous.
Check electrical connection cables regularly for damage.
Make sure the cable is disconnected from the mains when
checking.
Electrical connection cables must comply with the regula-
tions applicable in your country.
Single-phase motor
• The mains voltage must coincide with the voltage speci-
fied on the motor's rating plate.
• Extension cables up to a length of 25 m must have a
cross-section of 1.5 mm2, and beyond 25 m at least
2.5 mm2.
• The connection to the mains must be protected with a
16 A slow-acting fuse.
Only a qualified electrician is permitted to connect the ma-
chine and complete repairs on its electrical equipment.
In the event of enquiries please specify the following da-
ta:
• Motor manufacturer
• Type of current of the motor
• Data recorded on the machine's rating plate
• Data recorded on the switch's rating plate
If a motor has to be returned, it must always be dispatched
with the complete driving unit and switch.
Maintenance
• Overhauls, maintenance work, cleaning, as well as the
elimination of any malfunctions must only be under-
taken after turning off the motor.
• All protective and safety equipment must be reinstalled
immediately upon completion of any repair or mainte-
nance work.
• Clean and lightly oil the spindle thread of the tool hold-
er when changing tools.
• When possible, the tail stock sleeve should be removed
by unscrewing it, cleaned and then sprayed with a dry
lubricant. Grease the threaded spindle.
• Check the eccentric clamp of the tailstock as well as
the tool holder and adjust if necessary. In addition,
tighten the hex nut under the bracket.
• Check the drive belt and replace when necessary.

Accessories

Jaw chuck protection Fig. 18
When working with the jaw chuck (accessory), the jaw
chuck protection must be used.
Extension console, Fig. 19
When working on a piece with a max. diameter of up to
500 mm, the extension console which is used must be at-
tached on the frontal side. Thereby, the headstock is re-
moved from the lathe bed, rotated by 180°, attached to
the lathe bed and refastened. The standard tool support is
employed here.
Article
Screw chuck
Socket chuck Ø 30 mm
Socket chuck Ø 40 mm
Socket chuck Ø 60 mm
Driver plate Ø 80 mm
Three-jaw chuck Ø 100 mm
Four-jaw chuck Ø 125 mm
Extension console
Jaw chuck protection
Art. No.
7400 7200
7400 8600
7400 7300
7400 8700
7400 8800
7400 8900
7400 7400
8800 2756
8800 2758
english 13