Transport; Cleaning And Maintenance - Scheppach DP16SL Original Bedienungsanleitung

10.6 Depth stop (10) (Fig. 14)
NOTE:
When the clamping device is in the top position, the
drill bit's tip must be just slightly above the top of the
workpiece.
The depth stop (10) enables the drilling depth to be
limited. To do so, set the required drilling depth and
use the knurled nuts (11) to screw it tight against the
bottom stop (12).
10.7 Positioning the workpiece (Fig. 15)
Always place a base (A) (e.g. wood) between the ta-
ble and workpiece. This prevents the rear of the work-
piece splitting or breaking when drilling through. In
order to prevent the base turning uncontrollably, lean
it against the left of the column (5) as illustrated.
Warning
If the workpiece or the base is not long enough for
this, clamp it to the table, as otherwise, serious inju-
ries may occur.
Note
Use the machine vice (accessory) for smaller work-
pieces that cannot be clamped to the table.
The vice must be clamped or screwed to the table in
order to prevent injuries due to rotating workpieces or
the vice, and to prevent destroying the tool.
10.8 Drilling a hole
Use a punch or a sharp nail to mark the location to be
drilled on the workpiece. Before you switch the drill
on, lower the drill bit onto the workpiece and centre
it over the location to be drilled. Switch the machine
on and press the drill bit gently onto the workpiece so
that it can cut cleanly.
If there is insufficient downward pressure, there is the
risk that the drill bit will become hot.
If there is excessive downward pressure, there is the
risk that the motor (13) will block, the V-belt or the drill
bit will slip, the workpiece will come loose or the drill
bit will break.
When drilling metal, you may have to cool the drill bit
with suitable fluid.
10.9 Working with the laser (Fig. 16)
Switching the laser beam on at the switch (25)
Set the illustrated hole in the fixed point (B) on the
laser, prepare for drilling and drill the hole.
10.10 Countersinking and centre drilling
You can also use this tabletop drill for countersinking
or centre drilling. Note that countersinking must be
performed at the lowest speed while a high speed is
required for centre drilling.
30 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
10.11 Machining wood
Note that suitable dust extraction must be used when
machining wood, as wood dust can be harmful to
health. Wear a suitable dust protection mask when
performing work that generates dust.

11. Transport

The machine may only be lifted and transported on
the belt box or the base plate. Never lift by the safe-
ty equipment or the adjustment handles when trans-
porting.
Disconnect the machine from the mains in order to
transport.
Pay attention to the weight distribution when trans-
porting the machine (the machine is top-heavy). Only
transport the machine lying down and secured on a
suitable fixture.

12. Cleaning and maintenance

Pull out the mains plug before performing any
setting, maintenance or servicing work.
m Have tasks that are not described in this op-
erating manual performed by a specialist work-
shop. Use only original parts. Let the device cool
down before all maintenance and cleaning tasks.
There is a risk of burns!
Each time before using the device, check it for obvious
defects such as loose, worn or damaged parts, or that
screws or other parts are tight. Replace damaged parts.
Do not use cleaning agents or solvents. Chemical
substances could damage the plastic parts of the de-
vice. Never clean the device under running water.
Clean the device thoroughly after each use.
• Clean the ventilation holes and the surface of the
device with a soft brush or cloth.
• Remove swarf, dust and dirt with a vacuum cleaner
if necessary.
• Lubricate the moving parts regularly.
• Do not allow any lubricants to come into contact
with switches, V-belts, drive pulleys and drill lifting
arms.
Lubrication
All ball bearings are greased in the factory so that
re-greasing is not required.
Lubricate all grooves in the spindle (33) and the
toothed rack (4) regularly.
To lubricate the drive, move the axle down and insert
the grease into the spindle (33) from above (below the
top cover). Move the axle up and down a few times.
To lubricate the toothed rack (4), move the axle down
and grease the axle's outer surface.