Residual Risks - Scheppach DP16SL Original Bedienungsanleitung

• Switch the electric tool off immediately if the
tool attachment blocks. The tool attachment
blocks if:
- the electric tool is overloaded or
- it gets stuck in the workpiece to be processed.
• Do not touch the tool attachment after working
until it has cooled down. The tool attachment be-
comes very hot when working.
• Inspect the cable on a regular basis and only
have damaged cables repaired by an author-
ised customer service centre. Replace dam-
aged extension cables. This ensures that safety
of the electric tool is maintained.
• Store the unused electric tool safely. The stor-
age location must be dry and lockable. This pre-
vents the electric tool getting damaged by storage
or being operated by inexperienced people.
• Never leave the electric tool until it has come to
a complete standstill. Tool attachments that are
still moving can cause injuries.
• Do not use the electric tool with a damaged ca-
ble. Do not touch the damaged cable and pull
the mains plug out if the cable gets damaged
while working. Damaged cables increase the risk
of an electric shock.
Attention: Laser beam
Do not look into the beam
Laser class 2
Protect yourself and you environment from acci-
dents using suitable precautionary measures!
• Do not look directly into the laser beam with unpro-
tected eyes.
• Never look into the path of the beam.
• Never point the laser beam towards reflecting sur-
faces and persons or animals. Even a laser beam
with a low output can cause damage to the eyes.
• Caution - methods other than those specified here
can result in dangerous radiation exposure.
• Never open the laser module. Unexpected expo-
sure to the beam can occur.
• If the mitre saw is not used for an extended period
of time, the batteries should be removed.
• The laser may not be replaced with a
• different type of laser.
• Repairs of the laser may only be carried out by the
laser manufacturer or an authorised representative.
Adhere to the correct mains voltage!
Ensure that the mains voltage corresponds to the
specifications on the type plate.
26 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
Use an earthed socket!
The device may only be operated using a socket with
properly installed fuse protection.
Workplace safety
Ensure that the machine is stable and secure. If pos-
sible, secure the machine to a floor plate or a work-
bench.
Protection against electric shock!
Protect the device against moisture. The device must
not be moist nor operated in a moist environment.
Check the device and the mains connection cable
with plug prior to each use. Avoid physical contact
with earthed parts such as pipes, radiators, etc.
Protect against fire or explosion!
There are sparking components inside the device.
Do not use the device in the vicinity of combustible
fluids or gases. There is a risk of fire or explosion if
disregarded.

6. Residual risks

The electric tool is state-of-the-art and has been
built according to the recognised technical safe-
ty regulations. However, individual residual risks
can arise during operation.
• Danger to health due to the rotating tool if hair is
long and clothing loose. Wear personal protec-
tive equipment such as a hair net and close-fitting
clothing.
• Risk to health due to flying chips. Wear personal
protective equipment such as eye protection.
• Injuries due to the workpiece being ejected at high
speed due to improper holding or guiding, such as
working without the vice or stop.
• Health hazard due to electrical power, with the use
of improper electrical connection cables.
• Furthermore, despite all precautions having been
met, some non-obvious residual risks may still re-
main.
• Residual risks can be minimised if the "safety in-
structions" and the "Proper use" are observed
along with the whole of the operating instructions.
• Avoid accidental starting of the machine: the oper-
ating button may not be pressed when inserting the
plug in an outlet.
• Use the tool that is recommended in this manual.
This is how to ensure that your drill provides opti-
mum performance.
• Keep your hands away from the working area when
the machine is in operation.
• Before performing setting or maintenance work,
switch the device off and unplug the mains plug.