Installation; Connecting To The Power Supply - Scheppach capas 2 Bedienungsanleitung

Installation

Know your Pullover Mitre Saw (Fig. 1)
1. Pullover carriage
2. Motor
3. Upper blade guard
4. Lower blade guard lock lever
5. Trigger switch
6. Handle
7. Lower blade guard
8. Tungsten Carbide Tipped blade
9. End Stop
10. Extension support (optional)
11. Mitre scale
12. Mitre lock knob
13. Table support
14. Table insert
15. Turn table
16. Bolt holes
17. Base
18. Clamp
19. Fence
20. Extension fence
Technical Data
Motor
Blade
No load speed
Turn table
Mitre stops 0°, 15°, 22.5°, 31.6°,
45° left & right
Mitre angle range
Bevel angle range
Weight
Max. Capacity
Cross Cut at 90°
Mitre cut at 45°
Bevel cut at 45°
Compound cut at 45°
The noise levels of this machine during cutting are as fol-
lows:
maximum sound pressure level: 99dB(A)
Assembly
WARNING! For your own safety, never connect the
plug to power source outlet until all assembly
steps are completed and you have read and under-
stood the safety and operational instructions.
Lift the saw from the packaging and place it on your work
bench.
Installing the Dust Bag
1. Squeeze the metal collar wings ➁ of the dust bag and
put it on the motor area exhaust port ➀. (Fig. 2)
1120 W, 230V ~ 50Hz
ø 216 mm; ø 30 mm Bore
5000 min -1
ø 525 mm
48° left & right
-3° to 50°
23 kg
65 x 320 mm
65 x 220 mm
45 x 320 mm
45 x 220 mm
Installing the Extension Supports (Optional)
1. Slide the End Stop ① onto the back rail ➁ of the Ex-
tension Support. (Fig. 3)
2. Tighten the screw ① to lock the Extension Support.
(Fig. 4)
Note:
1. The Fig. 3 and 4 only show the installation of the right
extension support. Repeat these procedures for the
left extension support.
2. The End Stop may be installed on either side of the
extension supports.
Installing the Extension Fence
1. For mitre cuts, install the Extension Fence ① close to
the saw blade and tighten the lock knob ➁. (Fig. 6)
2. For bevel or compound cuts, install the Extension
Fence ① some distance from the saw blade. (Fig. 7)
3. For crown moulding cut, turn the Extension Fence ①
close to the saw blade. Tighten the lock knob (Fig. 8)
Setting the Tool
Note:
This tool is accurately adjusted before shipping from the
factory. Check the following accuracy and readjust if nec-
essary in order to obtain the best results in operation.
Adjusting the Bevel Stops at 90° and 45° (Fig. 9)
1. Loosen the Bevel Lock Handle and move the cutting
head all the way to the right and tighten the Bevel
Lock Handle ①.
2. Use a square to set the blade at 90° to the table.
3. If an adjustment is necessary, loosen the lock nut ➁
and adjust the bolt ➂ using the supplied wrench so
that the blade is 90° to the table.
4. Tighten the lock nut.
5. Adjust the bevel indicator ➃ to the 0 mark using the
screw ➄.
6. To adjust the 45° stop, follow the same procedure as
the 90° but move the cutting head to the left and use
the lock nut ➅ and bolt ➆.
Adjusting the Fence
1. Lower the cutting head and push in the lock pin.
Make sure the table is in 0 mitre position.
2. Place a combination square against the fence and
next to the saw blade. (Fig. 10).
3. If the blade does not contact the square, loosen the
three screws ①. (Fig. 11)
4. Adjust the fence so that the fence has full contact
with the square. Tighten the screws.

Connecting to the Power Supply

Check that the power supply and outlet used are in accor-
dance with your mitre saw. Have a look at the rating plate
of the motor or the rating on the mitre saw. Any changes
should always be carried out by a qualified electrician.
This is a double insulated tool which eliminates the need
for an earthed power supply system.
2