Loading The Magazine - Bosch GTK 40 Professional Originalbetriebsanleitung

OBJ_BUCH-1038-001.book Page 25 Wednesday, December 9, 2009 1:38 PM
Assembly
Connecting the Air Supply (see figure A)
Make sure that the pressure of the compressed-air sys-
tem is below the maximum permitted rated pressure of
the pneumatic tool. Firstly, set the air pressure to the
lower value of the recommended rated pressure (see
"Technical Data").
When in doubt, check the pressure at the air inlet with a
pressure gauge with the pneumatic tool switched on.
For maximum performance, the values for the supply-air
hose 17 (connection thread, maximum operating pres-
sure, inner hose diameter, maximum hose length; see
"Technical Data") must be observed.
The compressed air supplied should be free of foreign
material and moisture to protect the tool from damage,
contamination, and the formation of rust.
All fittings, connecting lines and hoses must be dimen-
sioned for the pressure and the required air volume.
Avoid restrictions in the air supply, e.g., from pinching,
kinking, or stretching!
Connecting the Air Supply to the Pneumatic Tool
– Empty the magazine 8.
(See "Emptying the Magazine", page 27)
For the following worksteps, a fastener can be dis-
charged when interior parts of the pneumatic tool are
not in the starting position due to repairs, maintenance
or transport.
– Connect the air connector 6 with a supply-air hose 17
equipped with an air-connection coupling 16.
– Check the proper function by placing the outlet 13 or
the rubber workpiece protector 1 of the pneumatic
tool onto a piece of scrap wood or wood material, and
discharging once or twice.
Bosch Power Tools
Downloaded from www.Manualslib.com manuals search engine

Loading the Magazine

Disconnect the air supply before making any
adjustments, changing accessories, or plac-
ing the pneumatic tool aside. This safety
measure prevents accidental starting of the
pneumatic tool.
Use only original Bosch accessories (see "Technical
Data"). The precision parts of the pneumatic tool such
as the magazine, the outlet and the shot duct are
matched to Bosch staples, nails and brads. Other man-
ufacturers use other steel qualities and sizes.
Using fasteners not permitted, can damage the pneu-
matic tool and cause injuries.
While loading the magazine, hold the pneumatic tool in
such a manner that the outlet 13 is not pointed at your
own body or at other persons.
GTK 40 (see figures B1 B2)
–
– Pull back the magazine slider 11 until the button of
magazine-slider lock 7 fully engages.
– Clean and lubricate the magazine slider 11 as required
and make sure that the magazine 8 is not dirty/soiled.
– Place a fitting strip of staples 18 over magazine 8.
The staple heads must face completely flush against
the surface of the magazine and the staple strips must
move easily in the magazine.
– Lightly pull back magazine slider 11 and press the but-
ton of magazine-slider lock 7 inward.
– Carefully guide the magazine slider to the front until it
touches the staple strip.
Note: Do not let the magazine slider snap back without
guiding it. Otherwise, the magazine slider could become
damaged, and there is danger of your fingers being
caught or pinched.
GSK 50 (see figures C1 C2)
–
– Press magazine lock 14 and at the same time pull mag-
azine 8 toward the rear to the stop.
– Clean and lubricate magazine rail 20 as required.
– Insert a fitting nail strip 19.
If possible, the nail tip should touch the magazine rail
20.
– Slide the nail strip in the magazine all the way to the
front.
– Insert the magazine until magazine lock 14 engages
again.
Refill the magazine when the red bars of refill indicator 15
can be seen halfway.
English | 25
1 609 929 U13 | (9.12.09)