Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
16 | English
Cordless rotary hammer
Impact energy per stroke ac-
cording to EPTA-Proced-
ure 05:2016
Tool holder
Max. drilling diameter
– Concrete
– Steel
– Wood
Weight according to EPTA-
Procedure 01:2014
B)
Recommended ambient tem-
perature during charging
Permitted ambient temperat-
ure during operation
C)
and
during storage
Recommended rechargeable
batteries
Recommended battery char-
gers
A) Measured at 20–25 °C with rechargeable battery PBA 18V 4.0
Ah W-..
B) Depends on battery in use
C) Limited performance at temperatures < 0 °C
Noise/Vibration Information
Noise emission values determined according
to EN IEC 62841-2-6.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 90 dB(A); sound power
level 101 dB(A). Uncertainty K = 5 dB.
Wear hearing protection!
Vibration total values a
(triax vector sum) and uncertainty K
h
determined according to EN IEC 62841-2-6:
Hammer drilling into concrete: a
h
Chiselling: a
=13.5 m/s
2
, K=1.5 m/s
h
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
1 609 92A 852 | (22.07.2022)
UniversalHammer
18V
J
2.0
SDS plus
mm
16
mm
13
mm
25
kg 2.4 (2.5 Ah)–2.7
(6.0 Ah)
°C
0 to +35
°C
–20 to +50
PBA 18V...W-.
AL 18...
=16.5 m/s
2
, K=1.5 m/s
2
,
2
,
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
Rechargeable battery
Charging the battery
Use only the chargers listed in the technical data. Only
u
these chargers are matched to the lithium-ion battery of
your power tool.
Note: Lithium-ion rechargeable batteries are supplied par-
tially charged according to international transport regula-
tions. To ensure full rechargeable battery capacity, fully
charge the rechargeable battery before using your tool for
the first time.
Inserting the Battery
Push the charged battery into the battery holder until it
clicks into place.
Removing the Battery
To remove the rechargeable battery, press the battery re-
lease button and pull the battery out. Do not use force to do
this.
Battery charge indicator
The battery charge indicator indicates the state of charge for
a few seconds when the on/off switch is half or fully pressed.
LED
3 × continuous green light
2 × continuous green light
1 × continuous green light
1 × slowly flashing green light
The three LEDs in the battery charge indicator flash quickly
when the overload protection has been triggered.If only the
middle LED is flashing quickly, then the temperature of the
rechargeable battery or the power tool is outside of the oper-
ating temperature range.Allow the battery and the power
tool to cool.
Recommendations for Optimal Handling of the
Battery
Protect the battery against moisture and water.
Only store the battery within a temperature range of −20 to
50 °C. Do not leave the battery in your car in the summer, for
example.
Occasionally clean the ventilation slots on the battery using a
soft brush that is clean and dry.
A significantly reduced operating time after charging indic-
ates that the battery has deteriorated and must be replaced.
Follow the instructions on correct disposal.
Capacity
75–100 %
40–75 %
15–40 %
0–15 %
Bosch Power Tools
Werbung
Inhaltsverzeichnis
