Makita DLS600 Betriebsanleitung Seite 31

Workpieces up to 46 mm high and 92 mm wide can be
cut in the following manner. 1.
workpiece with the vise.
2. Switch on the tool without the blade making
any contact and wait until the blade attains full speed
before lowering.
3. Gently lower the handle to the fully lowered
position to cut the workpiece.
4. When the cut is completed, switch off the
tool and wait until the blade has come to a complete
stop before returning the blade to its fully elevated
position.
Miter cutting
Refer to the
"Adjusting the miter
Bevel cut
WARNING:
After setting the blade for a bevel
cut, before operating the tool ensure that the saw
head and blade will have free travel throughout
the entire range of the intended cut. Interruption of
the saw head or blade travel during the cutting
operation may result in kickback and serious personal
injury.
WARNING:
While making a bevel cut keep
hands out of the path of the blade. The angle of the
blade may confuse the operator as to the actual blade
path while cutting and contact with the blade will result
in
WARNING:
The blade should not be raised
until it has come to a complete stop. During a
bevel cut the piece cut off may come to rest against
the blade. If the blade is raised while it is rotating the
cut-off piece
the
material to fragment which may result in serious
personal injury.
WARNING:
Always remove sub-fence when
performing bevel cuts. Failure to do so may cause
serious injury.
►
Fig.47
1. Loosen the lever and tilt the saw blade to set
the bevel angle (Refer
previously covered "Adjusting the
angle"). Be sure
the lever firmly
the selected bevel angle safely. 2.
the workpiece with the vise.
3. Switch on the tool without the blade making
any contact and wait until the blade attains full speed.
4. Gently lower the handle to the fully lowered
position while applying pressure in parallel with the
blade to cut the workpiece.
Secure the
previously covered
angle".
serious personal injury
maybe ejected by
blade causing the
to the
bevel
to retighten
to secure
Secure
5. When the cut is completed, switch off the
tool and wait until the blade has come to a complete
stop before returning the blade to its fully elevated
position.
NOTICE:
When pressing down the handle, apply
pressure in parallel with the blade. If a force is
applied perpendicularly to the turn base or if the
pressure direction is changed during a cut, the
precision of the cut will be impaired.
Compound cutting is the process in which a bevel angle
is made at the same time in which a miter angle is being
cut on a workpiece. Compound cutting can be
Compound cutting
performed at the angle shown in the table.
Miter angle
Left and right 45°
Right 52°
Left 52°
When performing compound cutting, refer to "Press
cutting", "Miter cutting" and "Bevel cut" explanations.
Cutting aluminum extrusion
►
Fig.48:
fence
4. Aluminum extrusion 5. Spacer block
When securing aluminum extrusions, use spacer blocks
or pieces of
in the
deformation
Use a cutting lubricant when cutting the aluminum
extrusion to prevent build-up of the aluminum material
on the blade.
CAUTION:
Never attempt to cut thick or round
aluminum extrusions. Thick aluminum extrusions
may come loose during operation and round
aluminum extrusions cannot
firmly
Cutting repetitive lengths
When cutting several pieces of stock to the same
length, ranging from 200 mm to 330 mm, use the set
plate (optional accessory). Install the set plate on the
holder (optional
in the
plate 2. Holder 3. Screw
Align the cutting line on your workpiece with either the
left or right side of the groove in the kerf board, and
while holding
the set
the end
the set plate with the screw. When the set plate is not
31 ENGLISH
Bevel angle
Left and right 0° - 45°
Left 20° - Right 45°
Left 45° - Right 20°
1. Vise 2. Spacer block 3. Guide
scrap as
figure to
of the
be
with this
accessory) as
figure. ► Fig.49:
1. Set
the workpiece, move
plate flush
of the workpiece. Then secure
shown
prevent
aluminum.
secured
tool.
shown
against