Makita DLS600 Betriebsanleitung Seite 19

Supporting the workpiece "cross handed" i.e.
holding the workpiece to the right of the saw blade
with your left hand or vice versa is very
dangerous.
►
Fig.1
5. Do not reach behind the fence with either hand
closer than 100 mm from either side of the saw
blade, to remove wood scraps, or for any other
reason while the blade is spinning. The
proximity of the spinning saw blade to your hand
may not be
may
6. Inspect your workpiece before cutting. If the
workpiece is bowed or warped, clamp it with
the outside bowed face toward the fence.
Always make certain that there is no gap
between the workpiece, fence and table along
the line of the cut. Bent or warped workpieces
can twist or shift and may cause binding on the
spinning saw blade while cutting. There should be
no nails
in
7. Do not use the saw until the table is clear of all
tools, wood scraps, etc., except for the
workpiece. Small debris or loose pieces of wood
or other
the
be thrown with high speed.
8. Cut only one workpiece at a time. Stacked
multiple workpieces cannot be adequately
clamped or braced and may bind on the blade or
shift during cutting.
9. Ensure the mitre saw is mounted or placed on
a level, firm work surface before use. A level
and firm
the
mitre
10. Plan your work. Every time you change the
bevel or mitre angle setting, make sure the
adjustable fence is set correctly to support the
workpiece and will not interfere with the blade
or the guarding system. Without turning the tool
"ON" and with no workpiece on the table, move
the saw blade through a complete simulated cut to
assure there will be no interference or danger of
cutting the fence.
11. Provide adequate support such as table
extensions, saw horses, etc. for a workpiece
that is wider or longer than the table top.
Workpieces longer or wider than the mitre saw
table can tip if not securely supported. If the cut-off
piece or workpiece tips, it can lift the lower guard
or be thrown by the spinning blade.
12. Do not use another person as a substitute for a
table extension or as additional support.
Unstable support for the workpiece can cause the
obvious and
be seriously
or foreign
the workpiece.
objects that
revolving blade
work surface
risk of
saw becoming unstable.
blade to bind or the workpiece to shift during the
cutting operation pulling you and the helper into
the spinning blade.
13. The cut-off piece must not be jammed or
pressed by any means against the spinning
saw blade.
blade and thrown violently.
14. Always use a clamp or a fixture designed to
properly support round material such as rods
you
or tubing. Rods have a tendency to roll while
injured.
being cut, causing the blade to "bite" and pull the
work with your hand into the blade.
15. Let the blade reach full speed before
contacting the workpiece. This will reduce the
risk of the workpiece being thrown.
16. If the workpiece or blade becomes jammed,
turn the mitre saw off. Wait for all moving parts
to stop and disconnect the plug from the
power source and/or remove the battery pack.
objects
Then work to free the jammed material.
Continued
loss of control or damage to the mitre saw.
17. After finishing the cut, release the switch, hold
contact
the saw head down and wait for the blade to
can
stop before removing the cut-off piece.
Reaching with your hand near the coasting blade
is dangerous.
18. Hold the handle firmly when making an
incomplete cut or when releasing the switch
before the saw head is completely in the down
position. The braking action of the saw may
cause the saw head to be
reduces
the
19. Only use the saw blade with the diameter that
is marked on the tool or specified in the
manual. Use of an incorrectly sized blade may
affect the proper guarding of the blade or guard
operation
20. Only use the saw blades that are marked with a
speed equal or higher than the speed marked
on the tool.
21. Do not use the saw to cut other than wood,
aluminum or similar materials.
22. (For European countries only) Always use the
blade which conforms to EN847-1.
Additional instructions
1. Make workshop kid proof with padlocks.
2. Never stand on the tool.
cutting tool is unintentionally contacted.
19 ENGLISH
If
using length
cut-off piece could get wedged against the
sawing
jammed workpiece could
downward, causing
of injury.
which
in serious
could occur if the tool is tipped or if the
confined, i.e.
stops, the
with a
cause
suddenly pulled
a risk
could result
personal injury.
Serious injury