Makita DLS600 Betriebsanleitung Seite 28

Lighting up the lamp
CAUTION:
This is not a rainproof light. Do not
wash the light in water or use it in a rain or a wet
area. Such a conduct can cause an electric shock and
fume.
CAUTION:
Do not touch the lens of the light,
as it is very hot while it is lighted or shortly after it
is turned off. This may cause a burn to a human
body.
CAUTION:
Do not apply impact to the light,
which may cause damage or shorted service time
to it.
CAUTION:
Do not keep casting the beam of
the light to your eyes. This can cause your eyes to
be hurt.
CAUTION:
Do not cover the light with clothes,
carton, cardboard or similar objects while it is
lighted, which can cause a fire or an ignition.
CAUTION:
Do not look in the light or see the
source of light directly.
To turn on the lamp, press the upper position (I) of the
switch. To turn off the lamp, press the lower position (0)
of the switch.
►
Fig.28: 1. Lamp 2. Lamp switch
NOTE: Use a dry cloth to wipe the dirt off the lens of
the lamp. Be careful not to scratch the lens of lamp, or
it may lower the illumination.
NOTE: Be sure to turn off the switch as turning on the
switch consumes the battery power.
Laser beam action
CAUTION:
Never look into the laser beam.
Direct laser
your
To turn on the laser beam, press the upper position (I)
of the switch. To turn off the laser beam, press the
lower position (0) of the switch. ► Fig.29:
switch
NOTE: Be sure to turn off the switch as turning on the
switch consumes the battery power.
Laser line can be shifted to either the left or right side of
the saw blade
the adjusting screw
►
Fig.30: 1.
1. Loosen the
by turning
counterclockwise.
2. With the
loosened, slide
screw to
beam may injure
eyes.
1. Laser
by turning
as follows.
Adjusting screw
adjusting screw
it
adjusting screw
the adjusting
the right
or
as
3. Tighten
firmly
where it stops sliding.
NOTE: Laser
adjusted
is
side surface of the blade (cutting position).
NOTE: When laser line appears dim and hard to see
because of direct sunlight, relocate the work area to a
place where there is less direct sunlight.
Aligning the laser line
Align the cutting line on your workpiece with the laser
line.
►
Fig.31
A) When you want to obtain the correct size on
the left side of workpiece, shift the laser line to the left
of the blade.
B) When you want to obtain the correct size on
the right side of workpiece, shift the laser line to the
right of the blade.
ASSEMBLY
WARNING:
Always be sure that the tool is
switched off and the battery cartridge is removed
before working on the tool. Failure to switch off and
remove the battery cartridge may result in serious
personal injury.
Hex wrench storage
The hex
as shown
When the hex wrench is needed it can be pulled
out of the wrench holder.
After using the hex wrench it can be stored by returning
it to the wrench holder.
►
Fig.32:
Installing or removing saw blade
WARNING:
Always be sure that the tool is
switched off and the battery cartridge is removed
before installing or removing the blade. Accidental
start up of the tool may result in serious personal
injury.
CAUTION:
Use only the Makita hex wrench
provided to install or remove the blade. Failure to
do
in
28 ENGLISH
left as
it goes.
the adjusting
at the
line is
so that
positioned within 1 mm from the
wrench is
in the
1. Wrench holder 2. Hex wrench
so may
overtightening
far
screw
position
factory
it
stored
figure.
result
or