Saturation Display; Audible Signal; Cleaning And Maintenance; Cleaning Agents - Constructa Cd646850 Gebrauchs- Und Montageanleitung

Saturation display

When the metal grease filters or the activated charcoal filter
become saturated, the relevant indicator flashes after the
appliance is switched off:
Metal grease filters: |
■
Activated charcoal filter: {
■
Metal grease filters and activated charcoal filter: | and {
■
If you have not yet done so, the metal grease filters should now
be cleaned or the activated charcoal filter replaced.
Note. The saturation indicator does not apply for non-renewable
activated charcoal filters that are inserted downstream of the
metal grease filter. These activated charcoal filters must be
replaced twice a year.
The saturation indicators can be reset while they are flashing.
Touch the z symbol to do this.
Switching over the display for air circulation mode
For air recirculation mode, the electronic controller must be
switched over accordingly:
The extractor hood must be connected and switched off.
■
Touch and hold the # and @ symbols at the same time until
■
"2" lights up for air recirculation mode (filters that cannot be
regenerated).
Touch and hold the # and @ symbols again at the same time
■
until "3" lights up for air recirculation mode (filters that can be
regenerated).
Touch and hold the # and @ symbols again at the same time
■
until the electronic controller has switched back to air
extraction mode (indicator 1 ).

Cleaning and maintenance

:
Risk of burns!
The appliance becomes hot during operation. Allow the
appliance to cool down before cleaning.
:
Risk of electric shock!
Penetrating moisture may result in an electric shock. Clean
■
the appliance using a damp cloth only. Before cleaning, pull
out the mains plug or switch off the circuit breaker in the fuse
box.
Do not use any high-pressure cleaners or steam cleaners,
Risk of electric shock!
■
which can result in an electric shock.
:
Risk of injury!
Components inside the appliance may have sharp edges. Wear
protective gloves.
Caution!
There is a risk of surface damage if you do not peel off the
protective film.Remove the protective film from all parts of the
appliance before using the appliance for the first time.

Cleaning agents

To ensure that the different surfaces are not damaged by using
the wrong cleaning product, follow the instructions in the table.
Do not use any of the following:
Harsh or abrasive cleaning agents, e.g. scouring powder or
■
liquid scouring cleaner,
Cleaning products with a high alcohol content,
■
Hard scouring pads or cleaning sponges,
■
Pressure washers or steam cleaners,
■
Cleaning products that dissolve limescale,
■
Aggressive all-purpose cleaning products,
■
Oven spray.
■

Audible signal

Switching on
With the fan switched off, touch and hold the # and ' symbols
at the same time for approximately 3 seconds. A signal will
sound as an acknowledgement.
When the signal tone is activated, ‚ will be lit.
Switching off
With the fan switched off, touch and hold the # and ' symbols
at the same time for approximately 3 seconds. A signal will
sound as an acknowledgement.
When the signal tone is deactivated, ‹ will be lit.
Lighting
The lighting can be switched on and off independently of the
fan.
Touch the N symbol.
Set brightness
Press and hold the N symbol until the required brightness is
reached.
C l e a n i n g a n d m a i n t e n a n c e
Note: Wash new sponge cloths thoroughly before use.
Note: Follow all instructions and warnings included with the
cleaning products.
Area
Stainless steel
Painted surfaces
Aluminium and
plastic
Glass
Controls
--------
Cleaning products
Hot soapy water:
Clean with a dish cloth and then dry with
a soft cloth.
Clean stainless steel surfaces in the
direction of the grain only.
Special stainless steel cleaning prod-
ucts are available from our after-sales
service or from specialist retailers.Apply
a very thin layer of the cleaning product
with a soft cloth.
Hot soapy water:
Clean using a damp dish cloth and then
dry with a soft cloth.
Do not use stainless steel cleaner.
Hot soapy water:
Clean with a soft cloth.
Glass cleaner:
Clean with a soft cloth. Do not use a
glass scraper.
Hot soapy water:
Clean using a damp dish cloth and then
dry with a soft cloth.
Risk of electric shock caused by pene-
trating moisture.
Risk of damage to the electronics
caused by penetrating moisture. Never
clean controls with a wet cloth.
Do not use stainless steel cleaner.
21