Maintenance; Optional Accessories - Makita DTW700 Betriebsanleitung

Proper fastening torque for standard bolt with max
impact mode (4)
• m
N
(kgf•cm)
400
(4080)
300
(3060)
2
200
(2040)
M16
100
(1020)
0 1
1. Fastening time (second) 2. Fastening torque
Proper fastening torque for high tensile bolt with
max impact mode (4)
•
N m
(kgf•cm)
300
(3060)
200
(2040)
2
M12
100
(1020)
0 1
1. Fastening time (second) 2. Fastening torque
NOTE: Hold the tool pointed straight at the bolt or nut.
NOTE: ([FHVVLYH IDVWHQLQJ WRUTXH PD\ GDPDJH WKH EROWQXW RU
LPSDFW VRFNHW %HIRUH VWDUWLQJ \RXU MRE DOZD\V SHUIRUP D WHVW RSHU-
DWLRQ WR GHWHUPLQH WKH SURSHU IDVWHQLQJ WLPH IRU \RXU EROW RU QXW
NOTE: ,I WKH WRRO LV RSHUDWHG FRQWLQXRXVO\ XQWLO WKH EDW-
WHU\ FDUWULGJH KDV GLVFKDUJHG DOORZ WKH WRRO WR UHVW IRU 
PLQXWHV EHIRUH SURFHHGLQJ ZLWK D IUHVK EDWWHU\ FDUWULGJH
7KH IDVWHQLQJ WRUTXH LV D HFWHG E\ D ZLGH YDULHW\ RI
IDFWRUV LQFOXGLQJ WKH IROORZLQJ $IWHU IDVWHQLQJ DOZD\V
check the torque with a torque wrench.
M24
(M24)
M22
(M22)
M20
(M20)
(M16)
2 3
1
M16
M16
M14
M14
M12
2 3
1
1. :KHQ WKH EDWWHU\ FDUWULGJH LV GLVFKDUJHG DOPRVW FRPSOHWHO\
voltage will drop and the fastening torque will be reduced.
2. Impact socket
• Failure to use the correct size impact socket
will cause a reduction in the fastening torque.
• A worn impact socket (wear on the hex end or square
end) will cause a reduction in the fastening torque.
3. Bolt
• (YHQ WKRXJK WKH WRUTXH FRH FLHQW DQG WKH FODVV
of bolt are the same, the proper fastening torque
ZLOO GL HU DFFRUGLQJ WR WKH GLDPHWHU RI EROW
• Even though the diameters of bolts are the
VDPH WKH SURSHU IDVWHQLQJ WRUTXH ZLOO GL HU
DFFRUGLQJ WR WKH WRUTXH FRH FLHQW WKH FODVV
of bolt and the bolt length.
 7KH XVH RI WKH XQLYHUVDO MRLQW RU WKH H[WHQVLRQ
bar somewhat reduces the fastening force of the
LPSDFW ZUHQFK &RPSHQVDWH E\ IDVWHQLQJ IRU D
longer period of time.
5. The manner of holding the tool or the material of
GULYLQJ SRVLWLRQ WR EH IDVWHQHG ZLOO D HFW WKH WRUTXH
6. Operating the tool at low speed will cause a reduc-
tion in the fastening torque.

MAINTENANCE

CAUTION:
Always be sure that the tool is
VZLWFKHG R DQG WKH EDWWHU\ FDUWULGJH LV UHPRYHG
before attempting to perform inspection or
maintenance.
NOTICE:
Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
To maintain product SAFETY and RELIABILITY,
UHSDLUV DQ\ RWKHU PDLQWHQDQFH RU DGMXVWPHQW VKRXOG
EH SHUIRUPHG E\ 0DNLWD $XWKRUL]HG RU )DFWRU\ 6HUYLFH
&HQWHUV DOZD\V XVLQJ 0DNLWD UHSODFHPHQW SDUWV

OPTIONAL ACCESSORIES

CAUTION:
These accessories or attachments
are recommended for use with your Makita tool
VSHFL¿HG LQ WKLV PDQXDO 7KH XVH RI DQ\ RWKHU
accessories or attachments might present a risk of
LQMXU\ WR SHUVRQV 2QO\ XVH DFFHVVRU\ RU DWWDFKPHQW
for its stated purpose.
,I \RX QHHG DQ\ DVVLVWDQFH IRU PRUH GHWDLOV UHJDUGLQJ
WKHVH DFFHVVRULHV DVN \RXU ORFDO 0DNLWD 6HUYLFH &HQWHU
• Impact socket
• Extension bar
‡ 8QLYHUVDO MRLQW
‡ 0DNLWD JHQXLQH EDWWHU\ DQG FKDUJHU
‡ 3LQ  6HW )RU '7: RQO\
NOTE: 6RPH LWHPV LQ WKH OLVW PD\ EH LQFOXGHG LQ WKH
WRRO SDFNDJH DV VWDQGDUG DFFHVVRULHV 7KH\ PD\
GL HU IURP FRXQWU\ WR FRXQWU\
11 ENGLISH