Specifications - Makita DTW700 Betriebsanleitung

ENGLISH (Original instructions)

SPECIFICATIONS

Model:
Fastening capacities
Square drive
No load speed
Impacts per minute
Overall length
Rated voltage
Net weight
• 'XH WR RXU FRQWLQXLQJ SURJUDP RI UHVHDUFK DQG GHYHORSPHQW WKH VSHFL¿FDWLRQV KHUHLQ DUH VXEMHFW WR FKDQJH ZLWKRXW QRWLFH
‡ 6SHFL¿FDWLRQV PD\ GL HU IURP FRXQWU\ WR FRXQWU\
‡ 7KH ZHLJKW PD\ GL HU GHSHQGLQJ RQ WKH DWWDFKPHQW V  LQFOXGLQJ WKH EDWWHU\ FDUWULGJH 7KH OLJKWHVW DQG KHDYL-
est combination, according to EPTA-Procedure 01/2014, are shown in the table.
Applicable battery cartridge and charger
%DWWHU\ FDUWULGJH
Charger
• 6RPH RI WKH EDWWHU\ FDUWULGJHV DQG FKDUJHUV OLVWHG DERYH PD\ QRW EH DYDLODEOH GHSHQGLQJ RQ \RXU UHJLRQ RI UHVLGHQFH
WARNING:
Only use the battery cartridges and chargers listed above. 8VH RI DQ\ RWKHU EDWWHU\ FDUWULGJHV
DQG FKDUJHUV PD\ FDXVH LQMXU\ DQGRU ¿UH
Intended use
The tool is intended for fastening bolts and nuts.
Noise
7KH W\SLFDO $ZHLJKWHG QRLVH OHYHO GHWHUPLQHG DFFRUG-
ing to EN62841-2-1:
Model DTW700
Sound pressure level (L
pA
Sound power level (L ) : 105 dB (A)
WA
8QFHUWDLQW\ .  G% $
Model DTW701
Sound pressure level (L
pA
Sound power level (L ) : 105 dB (A)
WA
8QFHUWDLQW\ .  G% $
NOTE: The declared noise emission value(s) has been
measured in accordance with a standard test method
DQG PD\ EH XVHG IRU FRPSDULQJ RQH WRRO ZLWK DQRWKHU
NOTE: 7KH GHFODUHG QRLVH HPLVVLRQ YDOXH V PD\
DOVR EH XVHG LQ D SUHOLPLQDU\ DVVHVVPHQW RI H[SRVXUH
Standard bolt
High tensile bolt
Max impact mode (4)
Hard impact mode (3)
Medium impact mode (2)
Soft impact mode (1)
Max impact mode (4)
Hard impact mode (3)
Medium impact mode (2)
Soft impact mode (1)
) : 94 dB(A)
) : 94 dB(A)
DTW700
BL1815N / BL1820 / BL1820B / BL1830 / BL1830B / BL1840 /
BL1840B / BL1850 / BL1850B / BL1860B
DC18RC / DC18RD / DC18RE / DC18SD / DC18SE / DC18SF /
WARNING:
Wear ear protection.
WARNING:
The noise emission during actual
XVH RI WKH SRZHU WRRO FDQ GL HU IURP WKH GHFODUHG YDO-
ue(s) depending on the ways in which the tool is used
especially what kind of workpiece is processed.
WARNING:
Be sure to identify safety mea-
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use (taking account of all parts of the operating
cycle such as the times when the tool is switched
R DQG ZKHQ LW LV UXQQLQJ LGOH LQ DGGLWLRQ WR WKH
trigger time).
Vibration
The vibration total value (tri-axial vector sum) deter-
mined according to EN62841-2-1:
Model DTW700
Work mode: impact tightening of fasteners of the maxi-
PXP FDSDFLW\ RI WKH WRRO
Vibration emission (a
8QFHUWDLQW\ .  PV
4 ENGLISH
DTW701
M10 - M24
M10 - M16
12.7 mm
-1
0 - 2,200 min
-1
0 - 1,900 min
-1
0 - 1,200 min
-1
0 - 500 min
-1
0 - 2,700 min
-1
0 - 2,400 min
-1
0 - 1,700 min
-1
0 - 1,000 min
170 mm
D.C. 18 V
2.3 - 2.7 kg
DC18SH
2
) : 19.0 m/s
h
2