Working With The Saw; Maintenance And Cleaning - ATIKA KGS 210 N Originalbetriebsanleitung

Working with the saw

Before starting to work consider the following safety
advices to keep the risk of injuries as small as possi-
ble.
 Saw blade OK?
 Workplace tidied?
 You may not start to operate the machine until you have
read these original instructions, observed all the instructions
given and installed the machine as described!
Make sure before each sawing process that the ma-
chine stands safely.
Before making adjustments to the saw settings (e.g. re-
placing the saw blade, setting the work piece stop, etc.)
 Switch off device
 Wait for standstill of the saw blade
 Pull out power plug
In any case, follow the instructions in the section "Nor-
mal intended use" and "Safe working" (safety instruc-
tions).
Safely support long work pieces with suitable means. For exam-
ple, use roller blocks or similar devices to support overhanging
work pieces.
Workpiece dimensions
Minimum dimensions
Length Width
140 mm 50 mm
Maximum dimensions
Straight cuts
Mitre cuts
Inclinded cuts
Double mitre cuts
Straight cuts
Bring the saw head into the vertical position and tighten the
incline fixing know (20).
Loosen die fixing screws for the rotary table (6) and turn
the saw head into the 0° position. Tighten the fixing screws
for the rotary table (6) again.
Place the work piece against the stop (7) and clamp it with
the vise assembly (34).
Switch on the saw
Wait until the saw blade has reached its full speed.
While holding the On/Off switch (2), pull the lock for the
pendulum cover (1) towards the handle.
Using the handle, gradually lower the saw head and cut
evenly through the work piece down to the slot in the rotary
table.
Hold the saw head in position until the saw blade is no
longer in the work piece.
Release the On/Off switch and turn the saw head up again.
14
Width Height
120 mm 50 mm
80 mm 50 mm
120 mm 30 mm
80 mm 30 mm
Mitre cuts
The mitre angle can be set left and right from 0° to 45°. The
table locks in place at frequently required positions.
Loosen the fixing screw for the rotary table (6) and turn the
saw head to the right or left to the desired angle.
Firmly tighten the fixing screw again.
Cut the work piece as described under "Straight cuts".
Inclinded cuts
The incline angle can be set 45° toward the left from the vertical
position (0°).
Loosen the incline fixing screw (20).
Incline the saw head to the left to the desired angle.
Firmly tighten the incline fixing know again.
Cut the work piece as described under "Straight cuts".
Double mitre cuts
Increased danger of injury exists with the double mitre
cut because of the saw blade being more accessible due to
its heavy incline. Keep your hands far enough away.
Loosen the fixing screw for the rotary table (6) and turn the
saw head to the right or left to the desired angle.
Firmly tighten the fixing screw again.
Loosen the incline fixing screw (20).
Incline the saw head to the left to the desired angle.
Firmly tighten the incline fixing know again.
Cut the work piece as described under "Straight cuts".

Maintenance and cleaning

Before each maintenance and cleaning work
 switch off device
 wait for standstill of the saw blade
 pull out power plug
Further maintenance and cleaning works than described in this
chapter shall only be carried out by the manufacturer or compa-
nies named by the manufacturer.
For maintaining and cleaning, removed security devices must
unconditionally be mounted properly and proved again.
Use only original parts. Other parts can result in unexpected
damages and injuries.
Cleaning

Observe the following to maintain the functionality of the
saw.
 Do not wash down device with water.
 Remove splints and sawdust only with a brush or vacuum
cleaner.
 Clean and oil all moving parts regularly.

Never use any grease!