Scope Of Delivery; Intended Use; Safety Information - Scheppach MST254 Original Bedienungsanleitung

A.) 90° stop angle (not supplied)
B.) 45° stop angle (not supplied)
C.) Allen key, 6 mm
D.) Allen key, 3 mm
E.) Phillips head screw (Laser)

3. Scope of delivery

• Sliding cross cut mitre saw
• 1 x Clamping device (7) (preassembled)
• 2 x Workpiece support (8) (preassembled)
• Sawdust bag (17)
• Allen key 6 mm (C)
• Allen key 3 mm (D)
• Sawblade (mounted)
• Operating manual

4. Intended use

The sliding cross cut mitre saw is designed to cross-
cut wood and plastic respective of the machine's size.
The sliding cross cut mitre saw is not designed for
cutting firewood.
Warning! Do not use the sliding cross cut mitre saw
to cut materials other than those specified described
in manual.
Warning! The supplied saw blade is intended exclu-
sively for sawing the following materials:
wood, wood-derived products (MDF, chipboard, ply-
wood, blockboard, hardboard, etc.), wood with nails
and 3 mm mild steel plates.
Note: Wood containing non-galvanised nails or
screws can also be safely cut when carefully handled.
Note: Do not use the saw blade to cut galvanised ma-
terials or wood containing galvanised nails. Do not
use the saw blade to saw firewood!
The equipment is to be used only for its prescribed
purpose. Any other use is deemed to be a case of
misuse. The user / operator and not the manufacturer
will be liable for any damage or injuries of any kind
caused as a result of this.
The equipment is to be operated only with suitable
saw blades. It is prohibited to use any type of cutting-
off wheel.
To use the equipment properly you must also observe
the safety information, the assembly instructions and
the operating instructions to be found in this manual.
All persons who use and service the equipment have
to be acquainted with this manual and must be in-
formed about the equipment's potential hazards. It is
also imperative to observe the accident prevention
regulations in force in your area. The same applies
for the general rules of health and safety at work.
www.scheppach.com / service@scheppach.com /
The manufacturer will not be liable for any changes
made to the equipment nor for any damage result-
ing from such changes. Even when the equipment is
used as prescribed it is still impossible to eliminate
certain residual risk factors. The following hazards
may arise in connection with the machine's construc-
tion and design:
• Contact with the saw blade in the uncovered saw
zone.
• Reaching into the running saw blade (cut injuries).
• Kick-back of workpieces and parts of workpieces.
• Saw blade fracturing.
• Catapulting of faulty carbide tips from the saw
blade.
• Damage to hearing if ear-muffs are not used as
necessary.
• Harmful emissions of wood dust when used in
closed rooms.
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial
applications. Our warranty will be voided if the equip-
ment is used in commercial, trade or industrial busi-
nesses or for equivalent purposes.

5. Safety information

General power tool safety warnings
m WARNING! Read all safety warnings, instruc-
tions, illustrations and specifications provided
with this power tool. Failure to follow all instructions
listed below may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future ref-
erence.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-oper-
ated (cordless) power tool.
1. Work area safety
a) Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
b) Do not operate power tools in explosive at-
mospheres, such as in the presence of flam-
mable liquids, gases or dust. Power tools cre-
ate sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while op-
erating a power tool. Distractions can cause you
to lose control.
+(49)-08223-4002-99 / +(49)-08223-4002-58
GB | 25