Inhaltsverzeichnis
Werbung
6. Starting up
6.1
Switching the Thor ON
About the start up process
To start up the Thor the sealed compartment of the Light Processor and the sealed compartment of the Laser Clusters must be
brought into a 'condition' which is safe for the electronics to operate (avoid moisture due to extreme cooling). In other words, the
temperature and humidity inside these compartments must be brought within specs prior to activating the lasers and Light Processor.
The time needed to bring the projector from a deconditioned state into a conditioned state depends on the ambient conditions
and can take several minutes. This process is called conditioning.
Start up checklist
1.
Check if the chiller is correctly installed. See documentation set of the chiller.
2.
Check if the chiller is equipped with the expansion unit for DMD cooling.
3.
Check if the Thor is installed onto a stable platform and all covers are installed..
4.
Check if all hoses are properly connected with the chiller and projector. .
5.
Check if the data cables between chiller and projector are correctly installed.
6.
Check if the projector is connected with the mains electricity.
7.
Check if the ambient temperature and humidity are within specifications..
8.
Check if the chiller, hoses and projector are completely acclimatized to the same ambient temperature.
9.
Check if the correct lens is installed for the application and the lens cap is removed from the lens. See chapter "Objektivinstal-
lation", Seite 20.
10. Check if the small drain tubes at the bottom of the projector leads to a water drain or to an open reservoir to capture the
condensed water.
Denken Sie daran, dass das Starten der ausgeschalteten Laser bis zu 10 Minuten dauern kann. Wenn es
zwischen einzelnen Vorführungen nur eine Pause von 30 bis 45 Minuten gibt, empfiehlt es sich, die Laser
eingeschaltet zu lassen und den Dowser zu schließen. Bei geschlossenem Dowser werden die Laser automa-
tisch gedimmt.
Start up procedure
1. Switch on the chiller. The status light of the chiller should light up white. See documentation set of the chiller.
2. Press the Power Switch to switch the projector ON.
As a result the Controller of the projector starts up. All other electronics remain off. The booting process is indicated by the blue
blinking backlight of the Standby button on the local keypad. Once the Controller is up and running the backlight of the Standby
button is changed to continuous white. This is the projector Standby mode. The status light of the projector also flashes green.
Anmerkung:The projector always boots up in the same mode (E.g. Standby or Operation) as it was switched off. This procedure
assumes that the projector was switched off in Standby mode.
3. Press the STANDBY button on the Local Keypad for three seconds or use the Communicator to put the projector in OPERATIO-
NAL mode.
As a result the backlight of the Standby button starts blinking green indicating the start up of all other projector electronics. Once
this initializing process is done the backlight of the Standby button is changed to continuous green. This is the projector Opera-
tional mode. The status light of the projector also lights up green (not flashing).
4. Press the LIGHT button on the Local Keypad for three seconds or use the Communicator to activate the lasers.
As a result the backlight of the Light button starts blinking green indicating the projector is in CONDITIONING mode. The laser
status light on the top of the projector flashes a few times and then lights up continuously white.
Once the projector is conditioned the backlight of the Standby button is changed to continuous green. Now the lasers are active
and light can come out of the projector. The status light of the projector remains green and the status light of the lasers remains
white.
5. Press the DOWSER button on the Local Keypad or use the Communicator to open the dowser.
Anmerkung:The state of the dowser (open or closed) when starting up the projector will be the same as when the projector was
switched off. This procedure assumes that the dowser was closed .
A
CHTUNG
Communicator-Touch-Panel.
When for any reason a restart of the projector is required, the content server should be restarted also.
60
:
Weitere Informationen zu Betrieb und Steuerung des Thor finden Sie im Benutzerhandbuch zum
R5906787 THOR 16/12/2016
Werbung
Inhaltsverzeichnis
