Watching A Dvd Image; Connecting A Dvd Player; Displaying A Dvd Image; Using The Scart Output Function - Pioneer PDP-436XDE Bedienungsanleitung

Enjoying through External Equipment

Watching a DVD image

Connecting a DVD player

Use the INPUT 2 terminal when connecting to a DVD player
and other audiovisual equipment.
Media Receiver (rear view)
I N O U T
SERVICE ONLY
CONTROL
OUT IN
ANT(DIGITAL)
INPUT 1
ANT i /o link.A
SELECT
INPUT
2 3
INPUT 1
Component cable
(commercially
SCART cable
available)
(commercially available)
When using
component cable,
select "COMPONENT"
for "Input Select" in the
menu. See page 55.
At the same time
connect a SCART
cable to input audio
signals.

Displaying a DVD image

To watch a DVD image, press INPUT 2 on the remote control
unit or press INPUT on the Media Receiver to select INPUT2.
NOTE
• If DVD images do not come in clearly, you may need to
change the input signal type setting using the menu. See
page 55.
• Refer to your DVD player operation manual for the signal
type.
OPTICAL
DIGITAL OUT COMMON INTERFACE
INPUT 2
R-AUDIO-L SUB
Y P B P R
WOOFER
COMPONENT VIDEO AUDIO OUTPUT
INPUT 3
HDMI HDMI BLACK WHITE
INPUT 4
SYSTEM CABLE
DVD player

Using the SCART output function

This function allows you to record DTV progremmes with a
connected VCR or other recording equipment while enjoying
watching the Plasma Display as usual. With this function, you
can also easily enjoy timeshift playback when a DVD recorder
(DVR) is in connection.
The following diagram assumes that you connect a Pioneer
DVR-920H/DVR-930H to the Media Receiver so that you can
enjoy timeshift playback with the recorder.
Media Receiver (rear view)
I N OU T
SERVICE ONLY
CONTROL OUT
ANT(DIGITAL)
INPUT 1
ANT
i /o link.A
SELECT
INPUT
2 3
INPUT 1
SCART cable
(commercially available)
SCART cable
(commercially
available)
AC IN
DVR-920H/930H
In addition to the above connections, you need to perform the
following:
• See "Switching the SCART output" (page 64) and select
"Fixed on DTV" for "SCART Output" in the Setup menu.
• On the DVD recorder (DVR), select the video/audio input
source matching the external input terminal to which the
Media Receiver has been connected. For this method, see
the operation manual that came with the recorder.
• Select the input source on the Media Receiver depending on
the terminal to which the output of the DVD recorder (DVR)
has been connected; for the above connection example,
select INPUT 2.
When you complete the above connections and setups, you
can then enjoy timeshift playback with the DVD recorder
(DVR). You can also select the 2-screen or picture-in-picture
mode to watch images coming from the DTV input source and
an external input source (INPUT 2 for the above connection
example) to which the output of the recorder has been
connected.
NOTE
• Some DVD recorders (DVRs) may not allow timeshift
playback. Check the operation manual that came with your
recorder.
• For details about connection and setting procedures, see the
operation manual that came with your DVD recorder (DVR).
IN
OPTICAL
DIGITAL OUT COMMON INTERFACE
INPUT 2
R-AUDIO-L SUB
Y P B P R
WOOFER
COMPONENT VIDEO AUDIO OUTPUT
INPUT 3
HDMI HDMI BLACK
WHITE
INPUT 4
SYSTEM CABLE
AV 2 (INPUT 1/DECODER) AV 1 (RGB) - TV
COMPONENT
VIDEO OUT
Y
COAXIAL IN PUT 3
P
B
P R
OPTICAL
R L
HDMI OUT AUDIO VIDEO S-VIDEO
DIGITAL
OUT PUT
AUDIO OUT
13
IN
CONTROL
63
En