WARNUNG:
Wichtige Sicherheits-
anweisungen!
Für die Sicherheit von Personen ist es
wichtig, die folgenden Anweisungen
zu befolgen. Falsche Montage kann zu
schweren Verletzungen führen!
Herstellererklärung/Stand der Technik
Der Antrieb wurde gemäß der anzuwendenden
europäischen Richtlinien geprüft und her gestellt.
Eine entsprechende Einbau erklärung liegt vor.
Sie dürfen die Geräte nur betreiben, wenn für
das Gesamtsystem eine Konformitäts erklärung
vorliegt.
Der Antrieb entspricht dem Stand der Technik
und erfordert qualifiziertes Fachpersonal bei der
Montage, Wartung etc.
Personal
Die fachgerechte Montage, Wartung, Instand
haltung und Demontage des Antriebs
darf nur durch eine Elektrofachkraft nach
DIN VDE 1000-10 durchgeführt werden!
Bestimmungsgemäßer Gebrauch
Der Antrieb ist ausschließlich für automatisches
Öffnen und Schließen von Kipp, Klapp und
Drehfenstern geeignet, auch zur Lüftung.
Beachten Sie die technischen Daten (insbeson
dere Öffnungsquerschnitt des Fensters,
Öffnungszeit und Öffnungsgeschwindigkeit,
Temperatur beständigkeit von Kabeln und
Geräten, Windlasten) sowie die gültigen
Bestimmungen. Bei weiteren Anwendungs
bereichen im Werk anfragen.
Stimmen Sie benötigtes Befestigungsmaterial
mit dem Baukörper und der entsprechenden
Belastung ab und ergänzen Sie es, wenn nötig.
Ein eventuell mitgeliefertes Befestigungs
material entspricht nur einem Teil der
Erfordernisse.
Alle nicht dem bestimmungsgemäßen
Gebrauch entsprechenden Einsatzfälle oder
Änderungen am Antrieb sind ausdrücklich
verboten. Bei Nichteinhaltung übernimmt
HAUTAU keinerlei Haftung für Schäden an
Personen oder Material.
Aufbewahrung von
Dokumenten/Einweisung
Bewahren Sie diese Montageanleitung für
den späteren Gebrauch und die Wartung auf.
Händigen Sie die Bedienungsanleitung dem
Endanwender aus und nehmen Sie eine
Einweisung vor.
2
WARNING:
Important safety
instructions!
The safety of personnel requires that the
following instructions be observed. Incorrect
installation may result in severe injury!
Declaration of Conformity/state of the art
The drive has been constructed and tested in
conformity with all applicable European directi ves.
A corresponding declaration of incorporation is
available. You may not operate the equipment
unless a declaration of conformity is available
for the overall system.
The drive complies with the state of the art
and requires qualified personnel for installation,
maintenance, etc.
Personnel
The professional installation, maintenance,
repair and disassembly of the drive must be
entrusted to trained electricians as specified in
DIN VDE 100010!
Intended use
The drive is only suitable for the automatic
opening and closing of tilt, outward opening
and turn windows, for ventilation, too.
Follow the technical specifications (in particu
lar, the opening cross section of the window,
the opening time and speed, the temperature
resistance of cables and devices, and wind
loads) as well as all applicable regulations.
Consult our factory for any additional applica
tions.
Select the required mounting material in
accordance with the structure and the respec
tive load and use additional mounting material
if necessary. Any included mounting material
will only correspond to parts of the required
material.
Any individual applications or modifications
of the drive which are not in compliance with
intended use are explicitly prohibited. HAUTAU
shall not be liable for any damage to personnel
or material resulting from noncompliance with
this provision.
Storing documents/instructions
Store these instructions for future reference
and maintenance. Make these installation
instructions available to the end user and
provide instructions.