Samsung SMO-150TRN Bedienungsanleitung Seite 13

[PATTERN A]
CH MOTION ALARM
CH1 OFF
CH2 OFF
CH3 --
CH4 OFF
CH5 OFF
CH6 OFF
CH7 OFF
CH8 OFF
• Choose On/Off for the Motion, Alarm and Door-Bell features for all 8
cameras.
• Press the MENU button after completing the settings to return to the
ALARM Menu.
• Repeat the same for PATTERN B.
• The "--" will be displayed when it is not connected to the accessories.
RECORD...
• Select "RECORD..." using the Rotary Wheel and press ENTER to dis-
play the following screen.
[RECORD]
REC TYPE
REC OUT
AUDIO RECORD
SPOT - OUTPUT
REC TYPE
• NOR : Used for recording with a normal VCR. The picture is dis-
played according to the "REC OUT" set values (FIELD, FRAME).
• TLV: Used for recording through a time lapse VCR.
REC OUT
It is valid when the REC TYPE is "NOR".
• FIELD : Records at 1/50 seconds (PAL), 1/60 seconds (NTSC).
• FRAME : Records at 1/25 seconds (PAL), 1/30 seconds (NTSC).
AUDIO RECORD
Sets the channel that sends Audio signals to the recoding output.
SPOT-OUTPUT
Sets the output channel for SPOT which will intensely monitor that
channel.
• Press the MENU button after completing the settings to return to the
SYSTEM SETTING Menu.
HIDDEN CAMERA
• Select "HIDDEN CAMERA..." using the Rotary Wheel and press
ENTER to display the following screen.
[HIDDEN CAMERA]
CH
CH1
CH2
CH3
CH4
CH5
CH6
CH7
CH8
DOOR-BELL
-- OFF
-- --
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
NOR
FRAME
CH1
CH1
LIVE P.B.
OFF OFF
OFF OFF
ON OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
• Turn the Hidden Camera On/OFF of in LIVE Mode and P.B. MODE
for each channel.
• Press the MENU button after completing the settings to return to the
SYSTEM SETTING Menu.
SEQUENCE
• Set the Switching Interval for Sequence Mode. You can set the time
between 1 sec and 30 sec.
SYSTEM ID
• This function allows the user to control a single monitor using the
remote control when multiple (up to 10) monitors are linked together.
Only those monitors with IDs matching the Remote Control ID will be
controlled by the remote control.
CH1
MONITOR ID:1
CH4
CH7
• Setting: The default value of the monitor and the remote control is "1".
The value of the Monitor ID can be set from 0 to 9 by accessing the
System ID Setup mode under the System Setting menu. Press the
System ID button on the remote control to display the Monitor ID and
the Remote Control ID as shown above. With system ID button
pressed, enter the desired number by pressing the corresponding button
(0 to 9) to set up the Remote Control ID. The OSD will disappear three
seconds after the last button is pressed.
PASSWORD CHECK
• Turns the Password Check On/OFF for entry into the SETUP MENU.
• When PASSWORD CHECK is "ON" for entry into the SETUP
MENU, the following screen will appear and the first space for a num-
ber will be selected.
• Select the first digit of the Password using the Rotary Wheel and press
ENTER to move to the next digit. Repeat this step to enter the six-digit
password and press ENTER to return to the SETUP MENU.
• If the Password is not correct, "ERROR TRY AGAIN" will appear at
the bottom of the screen. The message will disappear after the first
digit of the Password is entered. Repeat this step until you have entered
the six-digit password then press ENTER to move to the SETUP
MENU. If the number is entered incorrectly more than three times, the
display will return to the previous menu.
Eng-13
CH2 CH3
REMOCON ID: 1
CH5 CH6
CH8
[PASSWORD CHECK]
++++++++++++++++++++++
+ - - - - - - +
++++++++++++++++++++++